Duck boat blind designs 2014,boat plans reading strategies,boat charter outer banks nc hotels - How to DIY

Published 05.04.2016 | Author : admin | Category : Diy Sailboat Plans

Since I shot my first duck at age 12, I’ve come to the conclusion that waterfowl hunting is more fun when you set up an ambush and entice the birds in close.
Waterfowl hunting is exciting — and it is even more satisfying when we share the experience. Cabela’s manufactures numerous waterfowling blinds, including the Northern Flight Boat Blind.
Gator-Tail produces the Quackhouse, a unique barge-style blind designed for up to three hunters.
If you feel the post above is in bad taste or violates the Rules Of Conduct please report it to the Lake-Link Moderators. No portion of this website can be used or distributed without prior written consent of Lake-Link, Inc. He now hunts the same lakes where he once guided anglers, including his favorite, Lake Wisconsin, a huge public reservoir that is 14 miles long. Hogland does a good bit of work with electricians on large commercial job sites, so he knew he could make the blind’s supports out of EMT. Using a pipe bender, each support pole is curved inward at a 90-degree angle at the top and bottom. The front support poles bend 90 degrees inward at the bottom to provide the same 6- to 8-inch pivot point axles, then rise to a height of 34 inches before being bent inward approximately 45 degrees to provide an overhang of 14 inches.
Bottom axles are attached to the casting platforms and seats with metal conduit straps that are screwed through the carpet and into the aluminum with self-tapping screws. Hunter’s Specialties blind material is attached to the front of the blind, but is only zip-tied to the angled top section. Brown or camouflage waterproof tarp material is attached to the rear frames using zip ties to secure only the top sections above the 90-degree curves. Hogland’s boat has a fishing seat in the stern and one in the bow, plus a live well on one side where one or two hunters can sit. Sure, a conveniently located tree trunk or other natural cover is sometimes all a waterfowl hunter needs for concealment.
Blinds are a big part of the ruse, and for my money, the single most important piece of hunting equipment that makes waterfowling a social success. After all, it’s not only the ducks and geese that make our hunting experiences enjoyable, but it is the people involved who help form lifelong memories in the field.
Designed in models suitable for boats from 14 to 18 feet long and beams up to 78 inches, they are fully adjustable. The Shaggy boat blind has become a favorite of serious hunters because it disappears in a wealth of environments, including river bottoms, cattail marshes, timber and even open water.


The 16-foot long by 7-foot wide barge features a comfortable box blind that can be towed or powered by a mud motor. It is just short of 11 feet long and 9 feet wide, making it a stable platform for up to five hunters. This lightweight blind can be carried by three hunters, yet still offers a full 6 feet by 10 feet of room to hunt in comfort. Like many hunters, he used EMT electrical conduit, but manufactured an extremely lightweight (and inexpensive) frame for easy set-up and take down. He did not want the blind to have a fixed support system, even though it would have been more sturdy.
Hogland used five on each side of his 17-footer, but other boats will require three to five supports depending primarily on the length, seat, console and storage compartment configuration.
The rear support poles of Hogland’s blind are 48 inches high and bend inward at the top to provide an overhang of 24 inches for the roof.
A shooting port runs the length of the boat between the front and rear frames, and the ends of the supports are taped to keep water out and painted to match the final camouflage pattern. Two holes are drilled into the top of each of the blind’s rear section “roof” support overhangs, one hole at the beginning of the 90-degree curve and one midway up the horizontal side. Once the correct fit is found by repeatedly folding the frames up and down, an overhand knot is tied on both sides of each hole in the frames.
A notch cut into the camouflage fabric allows the retriever to enter and exit from a casting platform that he had previously built into the stern of the boat. But more often than not, some type of commercial blind or blind-making materials is necessary to hide from the ever-watchful eyes of ducks and geese. Even blinds built for one can be positioned near enough that everyone involved in the hunt is part of the party. The sides and frame are made from a powder-coated steel, and the blind sets up using four pins in less than a minute.
The Shaggy blind consists of a mixture of cotton, polyester and burlap strips sewn to a tough polyester camouflage mesh background. Designed to handle up to four hunters, the blind can float in just 4 inches of water even when fully loaded.
The low-profile design and all-aluminum construction allow hunters to use the blind in a variety of environments. The blind covers are created from 1000 denier Cordura camouflage fabrics in a variety of patterns.
His rope and conduit pop-up blind will fit the needs of many waterfowlers, and received an honorable mention in the 2012 Boats & Blinds contest.


The bottom sections bend inward 6 to 8 inches, with this short length providing axles for the pivot points that allow the blind to rotate down toward the stern.
In the front section, one hole is drilled near the top end, one at the curve and another midway up the horizontal side.
Except for the rope at the top curve of the rear frame, all ropes are tied to a pair of carabiners that clip to each of the rear boat handles. Another short piece of rope is tied to the split ring and to a carabiner that clips to the bow eye.
Hunter’s Specialties blind material can be used in lieu of the tarp, but will not protect hunters from rain. The blind material extends partially around the outboard motor, but Hogland tosses a separate, loose piece of camouflage fabric over it for total concealment.
Sold as a kit, the blind frame is galvanized tubing and includes stainless brackets and hardware. The box blind accepts natural camouflage materials, has spud pipes for anchoring, includes navigation lights, a roll-down tarp to keep out wind and rain, plus a front and rear door for easy blind access. Accessories including lockable cover, interior lights, bilge pump, flip top, gun holders and spud poles.
You can take your boat to Hunter’s Design and let them build the blind for you, or purchase frameworks and fabric to do the work yourself. This short piece of rope takes up all of the tension for the final adjustments and any field adjustments.
Various covers are available, including marsh grass, prairie grass and die-cut camouflage in Seclusion 3D.
Designed to fit boats from 14 to 20 feet in length, the blind takes about two hours to assemble.
Accessories include a dog ladder, shelf for cook stove, galvanized trailer and the Go-Devil mud motor of your choice. The blind folds down in 30 seconds and can be strapped for secure transport on the highway.



How to make a cardboard pirate ship playhouse nz
Sportcraft boats for sale in ohio free
Free diy pontoon boat plans australia
Pontoon boats for sale in west palm beach outlets


Comments to «Duck boat blind designs 2014»

  1. bakinskiy_paren writes:
    Your youngsters are travel to Nova Scotia on business.
  2. ANGEL writes:
    Operation downward, is that a "rebound" spike could that.