After looking at various options and doing the costings, we decided to go with the 4C guide system.
Rob,Is that a Mid America trailer ?I was loading the pontoon in a strong cross wind and this is what happened to me.
I know you guys have seen this before, but I think a 2x4 in between those would help a bunch.I have more than just one brace but I have hit mine from the side pretty hard a couple of times and the braces have held good.
Pontoon Boat Trailer Plans Pontoon Boat Trailer Plans Bunk trailers are perfect for those who walked in the water.
If you'd like to see your shipping cost, add the item to your "Shopping Barge" and then use our Shipping Rates Calculator on the next page.
Pre-Galvanized SteelPre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. I painted these first and then put the pvc tubes on and then installed them on the trailer. The picture shown above has the bracket mounted backwards from the instructions in the package. My trailer came with nice guide on posts mounted between the toons so I am lucky in that regard.
With some of those last posts, makes me wonder if I shouldn't make some horizontal guides instead of a verticle guilde. I found a source of the bunk brackets themselves in which I'm really needing for my trailer.
They attach to the rear of your trailer and extend out of the water, providing a visual target to center the boat's pontoons around. The galvanized steel support posts mount horizontally on top of or below your trailer's frame rail.


The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Product is great and is a exactly what I needed in aiding me with the loading of my 24" tritoon boat.
I did receive them in a timely manner,I will save your email and will let you know how they work. It did not come with rear tie down straps and the dealer said I didn't need them because of the weight of the motor. But the supplier didn't get back to me with the one key measurement I'm needing to ensure the brackets will actually work on my trailer.
I had to lower the front of each guide by approx 2 inches and this is the result.That's enough for one night.
If you are included in business where you require that this type of vehicle of h2o for all types of h2o bodies then it is better to buy mix trailers. The guide posts are hot dip galvanized for long life with covers made from high impact non-marking molded PVC. Just slide the posts into the boat guide supports and secure the posts so that the distance between the bunks correctly matches the width of your boat. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted. Whether the post is situated facing outboard or inboard is up to you, so you can mount it in whichever position best suits your trailer setup.
The type of elements that you need to buy essentially depends on the type of marine that you're driving your boat. I used it on my 22 foot off shore fishing boat trailer to act as a guide on the rear of the trailer when loading my boat.


I now have instructions and the cross brace is still utilized (a length of 2x4) but cannot be fitted until final spacing and setup is complete.Impressions so far - a good product from first impressions but let down by customer service via emails and lacking documentation. I installed rollers on the inside and mounted my trailer lights near the top of the brackets to keep them out of the water when loading and unloading the boat. Well this guy and his buddy come over and say watch this put the small of their backs against the toon stood up and nudged her on perfect! The two times we had it out we were only off by an inch.My trailer has eyes on the inside of the brake lights. I don't have straps on it here, but put the straps right between the bunks and up to the eye at the top of the toon.I know I need to get my new bunk carpet on!
Trailers for boats are very crucial for individuals whose lives and businesses requires trading in drinking water. Also bunk trailers price significantly less than roller trailers but they are not very practical for use in shallow waters. The types of trailers that can be obtained on the market vary quite different types models shapes and price range. There are basically two different types of trailers for boats which are widely known in the industry.



Build your own inboard boat accessories
Pontoon boat rental chicago il 95th