Picture Of Basement Under Stairs Storage Search for: BEGIN TYPING YOUR SEARCH ABOVE AND PRESS RETURN TO SEARCH.
How to Build Under-stair Basement Storage Shelves - Adding Extra Storage Space - Built-ins, Shelves & Bookcases. The design shown here gives you storage spaces of different sizes, including a tall narrow box for items such as brooms or skis. Like drywall screws, particleboard screws have a sharp point, an aggressive thread, and a bugle-shaped head. The boxes shown fit under a staircase with a 45-degree pitch: For every 12 inches the stairs rise, they run (travel horizontally) 12 inches. If your stair slope is more gradual, your boxes will need to be wider to fit; more steep and the boxes will be narrower. Many lumberyards and home centers have a panel saw -- the best tool for cutting sheet goods to size. Ask your dealer to make the crosscuts described in Steps 1 and 2 and the rip-cuts described in Step 3. Use a circular saw with a straightedge jig to make all the cuts that go completely across the ripped pieces (see the cutting diagrams). When joining the top and bottom of the long box to the sides, put wax paper under the joint to keep glue squeeze-out off your bench.
Always have a small bucket of water, a sponge, and a towel handy when working with wood glue. Turn over the long box assembly, apply glue to the top and bottom edges of the second side, and screw it into place between the top and bottom. Taking on a project like basement stairs may seem simple enough, but for all the ways they’re similar to ordinary stairs, there are a few key differences to keep in mind. While any staircase needs to be built with careful measurements and safety in mind, basements are frequently dark and not constructed to standard dimensions.
Check your local building codes to see if there are any restrictions or guidelines that you must follow when building your new basement steps. If a permit is required for this type of construction, don't try to dodge the permit fee just because the stairs will be invisible under your house. Measure the distance starting from your basement floor straight up to the basement ceiling. Convert the total run from feet to inches and then divide that number by the number of treads to determine the width for your stair treads. In a typical room, adding together the riser height and tread width should result in 17-18 inches, but since the basement floor may or may not be a standard height from the floor above, be prepared for unusual measurements.
Build the staircase as you would any other, but be prepared to work in cramped spaces and answer questions that wouldn't apply to stairs in finished rooms. To make sure you receive our emails in your Inbox, drag them from the new Gmail Promotions Tab over to your primary Inbox. I recently converted the 3D deck & shed plans into sketchup so that others can benefit. It was a lot of fun figuring out how to lift that heavy, wet, pressure-treated beam onto the posts all by myself.


The posts weren’t small either, when you consider they are almost 6 feet underground! Another month or so would pass before I could finish my custom shed doors, but I’m happy with the result. For longevity did you use an ice and water shield or rubber under the aluminum to protect the OSB?
Many many thanks again for doing this I can’t imagine how many homeowners you have inspired by the articulate details provided here. I am interest to know how the aluminum flashing was attached to the house so there would be no leaking. I’m trying to understand how you managed to concrete the floor of your shed with the two posts already installed. I assume for the inside plywood wall closest to the house you prebuilt the wall with the plywood and lifted it into place.
I was hoping to find a flexible material that could be used between the bottom of the deck and the top of the shed for both esthetic reasons and to keep things from moving in. The deck is attached to the house and the post supporting the deck have attached to footings below the frost line. The boxes are so quick and easy to build that you'll have no trouble adapting them to your storage needs as well as to the size and pitch of the space under your stairs. They are made from inexpensive particleboard without finish, although you can paint them for a more attractive look.
There's one important difference: Particleboard screws have a self-tapping tip that pulls the screw into the particleboard without predrilling. A panel saw has a rack that holds the panel upright and a circular saw that runs on tracks to easily make accurate rip-cuts and crosscuts anywhere on the panel.
This will speed your work when you get home, and the smaller pieces will be easier to transport.
Rip-cut the particleboard on the tablesaw, and have someone support the sheet at the back of the saw table. With your circular saw and straightedge jig, crosscut one of these pieces to 72 inches to make the back (I) of the tall box. Draw lines across both pieces with a framing square to show where to locate the bottom of the shelves. Have someone hold each shelf along the layout line as you glue and screw the shelf to one side.
Put the top in place, make sure the edges are flush, then screw it in place, again with three screws for small boxes, five screws for large boxes.
Put the bottom (A or D) in place, check that the edges are flush, and secure with three or five screws into each side.
The wax paper will easily pull away without getting stuck to your project the way newspaper will. Lay the box on its face and screw the back in place -- five screws per edge for large boxes, three screws per edge for small boxes. You can wipe away glue that squeezes out of joints with a damp sponge and dry your hands with the towel.


Finally, screw the back in place using 12 screws along each side, five screws across the top and five screws across the bottom. Depending on how often you plan on taking guests down to your basement, you may not need to add any frills or work to make them pretty. Obtaining a permit and following building codes will protect you and your family from both accidents and lawsuits.
Depending on local building codes and where you want the stairs to end, you may have to build your basements stairs in an L shape or with a small landing. Each basement is different, so you have to plan ahead and make these determinations for each individual space.
The following youtube video covers some important factors to consider when building such a deck. I wanted my shed to look as nice as I could make it… so I wrapped it in matching vinyl siding. I live in central NC and I’m considering doing the same thing under my screened in porch.
Extend these lines across the outsides of the panels so you will see where to drive screws.
The easiest option is building the stairs straight down, but that may not be practical in the space allowed.
Make all of the risers and treads the same by averaging the measurements across the total length of the stairs. My trailer-lift project may have been my most gratifying project, but my shed has been the most useful. For building a shed under a deck, you can screw sheets of corrugated metal or fibreglass roofing to the furring strips. Particleboard readily absorbs moisture that makes it swell, and it will crumble if it gets wet. Screw the top (A or D) to the side, using three screws for small boxes and five screws for large boxes. I decided to put my shed entry on the left side of the deck, so I had to dig the hillside down and create a patio for the doorway. Good thing I allowed space for the concrete to heave in winter… because it did just that!
You can cut and install wood lattice around the deck foundation, so as to hide the storage area from view. I am currently looking for someone to build me one like this so I can park the motorcycles during the winter clearing the garage for the cars!. This inexpensive grade of plywood, intended for exterior sheathing, is made with water-resistant glue. For this purpose thicker lattice should be used, as it holds up better than the thinner lattice.



Shed size in brookhaven ny
Storage facilities 46220 apartments
Garden sheds for sale in kettering northamptonshire
Storage solutions 4 u jobs


Comments to «Build a basement under my shed»

  1. KRASOTKA_YEK on 31.05.2014 at 12:18:22
    The satisfaction of constructing one thing with your personal two hands your own.
  2. TeNHa_H on 31.05.2014 at 12:57:58
    Shop around the nook, Moduline.
  3. YUJNI_SEVER on 31.05.2014 at 13:14:35
    Shed, which began life can.