Please Select Username to appear on public areas of the site like community and recipe comments.
This workbench is simple enough and cheap enough that you can make it in a morning, and yet it's big enough for serious woodworking and hobby projects. All the dimensions and pieces are shown in Figures A, B and C, and keyed to the Cutting List in Additional Information (below). Expert advice from Bob Vila, the most trusted name in home improvement, home remodeling, home repair, and DIY. Designed for building small aircraft, this work table is built from easy-to-find materials and features simple yet rigid construction. This workbench from The Family Handyman perfectly suits those who work in a garage or basement (any space that is shared with other family activities).
If you are looking for a mobile or small-space solution—or you want a secondary work surface to complement an existing bench—consider this idea from Woodsmith: a rolling tool cabinet outfitted with a solid top. With this workbench plan even a beginner can build a workbench strong enough to hold a V-8 engine! Use this simple workbench plan to build a sturdy, tough workbench that'll last for decades.
For the names of the parts and their dimensions, see the Cutting List in “Additional Information” below.
Santa brought me a Lowe’s gift card which I decided to turn into a workbench for my garage. I measured and pre-drilled the tops of the legs for attachment to the outside of the frame. With the table still face down on the driveway, I attached two fixed casters to one end and two locking swivel casters to the other. I wanted a storage shelf to make use of the space under the table to help get some boxes and tools off the garage floor. Finally, I used my random orbital sander and some 220 grit paper to clean off the pencil marks on the top.
As you can see, only 3 days into its existence and my new workbench has already found a permanent home in my garage.
That is a fabulous workbench (if the words fabulous and workbench should be allowed to coexist in the same sentence). The 2×8s are holding up fine under about a continuous 200# static load that is fairly evenly distributed.
I was going to make it 2' wide but after thinking about it I didn't think that'd be wide enough and went with 32".
I was going to use pegboard behind it but since I was covering my walls in OSB anyway I just put some behind my workbench and used 3" drywall screws to hang tools.
This free workbench plan from Wood Magazine is for building a workbench that also serves as an out feed table for a tablesaw.Download the PDF of the workbench plan and use the instructions to build this sturdy and functional workbench.
This sturdy workbench plan includes 48 pages of detailed instructions, illustrations, photos, and more.Your finished workbench will be a mobile workbench with a large work top, drawers, and cabinets.
If the hassle of clearing a workspace is making you put off that project you've been promising your significant other for weeks, have we got a project for you! The beauty of this garage workbench is that it takes advantage of that narrow space between the garage door and the side wall most garages have. Place the miter saw in its permanent position and measure the distance from the front of the fence to the wall.


Add pegboard, a bench vise and a few other accessories and you'll have a serious work center.
Use gallon paint cans to support the lower shelf frame when you're attaching it to the main workbench legs. Please consider updating your browser to the latest version of Internet Explorer or Google Chrome. Though it’s able to withstand a banging, the table is still lightweight and compact enough to be portable. The setup includes a stable surface for hobby or repair projects, a built-in pegboard for storage, a shop light, plus a recessed shelf that allows for seating. A small vise and a power strip are included here, along with magnetic and pegboard tool storage, not to mention the storage provided by the cabinet drawers. This is standard kitchen counter height and is ideal for medium duty work on smaller items while standing.
The cheapest and simplest solution turned out to be two sections of 2X8 cut to length and screwed to 2X4 cross members. Also, easing the sharp corners will lessen the inevitable impact on my hip bones and my girls’ little heads. Made as four individual benches then fastened together at the ends for versatile future uses.
This sturdy workbench will only cost you $20 to build!Detailed instructions, a material list, and lots of pictures will make this workbench plan easy to carry out. A fold-out work table, a roll out table saw stand, a miter box table and lots of storage—cabinets, drawers, pegboard and shelves. Nail the cross supports to the rails for the two bench sections and the shelf section with two 16d nails at each joint.
Measure and mark that distance from the wall and snap a chalk line on the left table to align the extended fence. The base is made of affordable dimensional lumber, with joints that are both glued and bolted, meaning this bench is not only a thrifty option, but a sturdy one, indeed. The top uses two sheets of laminated MDF, and the plan incorporates handy features like bench dog holes and a woodworking vise.
This is a purely functional design that is big enough to support a couple of bench-top power tools while leaving enough workspace to spread out on.
Using an awl punch, I marked the spots to be drilled (using the punch keeps the drill bit from walking as it starts).
Two 2X4s were cut to 66″ long, divided into three sections and pre-drilled for screws. If it wasn’t I would have had to stood it up and tweaked on it a bit until it was (before the glue dried).
I could only get two screws in each caster but the weight of the leg was mostly centered over the caster body so it should work fine. Not only does this design support plenty of weight, but it also quite effectively ties the legs together and strengthens the base of the table. At this point I could have applied any number of finishes to my new workbench but instead I decided to leave it unfinished.
I’m going to use it for my ski tuning needs as well as for whatever it will be needed.
We are donating $10 of each blue star subscription to the Blue Ribbon Coalition to ensure that we will have trails to recreate on for years to come.


Notched in a 2x4 at the post tops then ran a 2x2 ledger down the inside of the back posts and across back of work bench to mount the pegboard to.
This bench layout lets you quickly fold out, slide out and pivot into position all the tools and work areas you need. If you can comfortably open the door and exit the car without maneuvering like a circus contortionist, you're in good shape. If you have one of the new slide miter saws, you may need more bench depth, but if you have a conventional miter saw, you may be able to make the bench narrower. However, be aware that alterations also affect the dimensions of the table saw module (Fig. The casters provide mobility so that the workbench can be moved around the garage or out into the driveway as needed. I figure this will hold it securely while allowing for a modicum of movement if the top should expand or contract a bit. I left the shelf high enough off the floor so that I could easily get under it to retrieve lost items.
I considered doing that when I built mine but was looking for the cheapest solution possible at the time. When you're done for the day, you can have everything stashed neatly away five minutes after you hear the dinner bell.
Plus, no fancy tools or know-how are required—just basic carpentry tools, a screw gun and a circular saw. The bench is divided into four equal-size bays, so you can shorten it by one or more bays, or reconfigure the tool and workspace positions. I used an old solid core door as the top since it was going to end up in a dumpster otherwise. The top 2x4 gives it backbone and the heavy duty shelf brackets do good holding up the front. Tons of tool and storage space on a lower shelf, in under-the bench roll-out drawers, inside low-cost upper utility cabinets and on Peg-Board will organize your tools and help your projects go faster.
Round up a free weekend to put this workbench together and you'll be knocking out that long-awaited baby crib (or is the kid already in eighth grade?) by Sunday night. Set it as close to a wall as you can, then measure the distance to the mounting holes in the front of the base.
Screw a 2x4 support to the backside of the legs on either side of the miter saw bay to support the shelf (Fig. I will likely staple some plastic netting to the sides and back so tools can’t fall out easily if I roll it around. Rest the bench frame on the supports, level it and clamp the front rail to the temporary support legs.
However, I’d more likely would just have built it using cedar or pressure treated lumber and left it unfinished as well.
The thing looks good, I almost want to build several and put extras in the unfinished downstairs!! Plumb the permanent legs and screw them into the front of the shelf rail and into the back side of the bench rail with four 3-in.




Yard storage shed plans materials
Barn sheds adelaide


Comments to «Easy diy workbench plans»

  1. KickBan on 13.09.2015 at 15:34:21
    Will present you how you can construct your in addition to this, the design is fairly simple and.
  2. LEDI_RAMIL_GENCLIK on 13.09.2015 at 23:15:57
    Doors will enhance the start fundraising, however she.
  3. Legioner on 13.09.2015 at 18:16:38
    Find that they are proof against and sturdy wall hung cabinets-what a distinction.
  4. ILOAR_909 on 13.09.2015 at 15:59:19
    Garage would not have fund pre-medical.