Woodshop lathe projects 8th,sheds for sale in yulee fl jobs,garage packages lac du bonnet grocery - Test Out

05.06.2014
American Woodworker magazine was acquired by F+W Media (parent company of Popular Woodworking) in 2014. Christopher Schwarz has helped many of us solve some pretty frustrating problems over the years. Enter your email address to subscribe to this blog and receive notifications of new posts by email.
Thats when I happened to be watching a few episodes of the Woodwright shop, where Roy kept bringing out his spring pole lathe! I wanted something that I could make in an evening, and which was simple enough to give me a chase to see if I actually liked turning. Then a few weeks ago I happened to discover that a local museum director, whom I know, had worked in Old Salem and that his spring pole lathe was still in operation there.
I’ve included a gallery at the bottom of my post walking thru the parts of the lathe. The foot is made by running one 2×4 the full length of the foot and then cutting four more to make a half lap joint. Very nice work and I can’t wait to hear more from you as you use it and see what you create. This is Part Two of our little project - if you want to go back and check on something we did earlier, then click HERE.
Like some of you who are reading this post about building a lathe, I then dove into research.
While I was in the early stages of design, I began looking for materials to suit my rough sketches and notes.
Once the bed was welded and surfaced, I suspended it off the mill with an angle plate that would make Paul Bunyan feel like a little man. For this operation (which I actually have a picture of), I lightly clamped the tailstock in place on the lathe and rigged up some jack screws to steadily advance the tailstock towards the headstock.
After this, I turned the quill sleeve and milled the necessary features that would attach the sleeve to the tailstock.


With the quill sleeve finished, I put the tailstock on the mill and indicated on the dowel pin that was pressed into the tailstock. It was a late night at the shop doing some last minute things before I could bring the lathe home. It didn’t take too many big Hickory bowls for me to consider a new motor for Big Blue.
I figured at this point, it was time to go for broke and throw the biggest heaviest piece I had on the lathe. Since so much of my lathe way built from materials on hand I didn’t spend more than $750 to acquire the remaining materials needing. The knobs were ordered from Grainger's but I couldn't find any that had a stud, so I made do by cutting the heads off some bolts, threaded them into the knob then drilled a cross hole and secured them with a pin. With that phase out of the way we turned our attention to making the housing for the headstock. Smitty's shop doesn't have a machine for rolling metal so I came up with the idea of taking a piece of pipe and cutting it in half along its length. By now we'd pretty much worked ourselves out of a job and the only thing left to do was clean up the little dingleberries left by the welding process. Judging from the smoke coming from Smitty's shoes, it looked like they were getting pretty warm so on his next pass I outstretched a bottle of beer, which forced him to come to a screeching halt - luckily near a convienent leaning spot.
The next day Richie and I went to Missoula and hauled the new lathe to its new home here in the Mission Valley.
More and more, I’d like to be able to incorporate turned components into my projects. Sure, if I was successful I’d build a better lathe, or invest in one down the line, but I wanted to figure it out on the cheap. The problem was that my bench needed to be clean to turn, and so I only did it a few times before I leaned it into a corner.
But then I went ahead and added legs to my lathe, and switched from a bungee to a 1′ spring.


Yeah there is very little friction which is good as I work out how tight everything has too be, but I could see the live centers being an issue in the long term. Beam on the mill with a 90? head attachment to true this surface to the area where the bed of the lathe would attach. Beam outside to weld some steel plates on the two open sides, effectively turning it into an enclosed pillar.
I didn't want anything fancy but at the same time they needed to have enough pizazz to make them look like they weren't just thrown together.
We made two banjos because I have a vintage tool rest that is 36" wide with two posts. Since I couldn't see any reason to purchase another motor and controller, I decided to use the DC motor from the lathe this new one will replace. The problem was that I just haven’t been able to talk myself (or my wife) into dishing out several hundred dollars to get started down that white rabbit. The string for the lathe ended up going through one of the dog holes, and it was held down by two hold fasts.
Now, this is really odd, but if you were to meet him on the street he'd present no indication whatsoever he could even spell "weld" but let me tell you, that Smitty is a welding fool! One could easily spend $1,000 dollars to get starting in wood turning, before you ever marred your first block of wood. They were wonderful and thoughtful examples of each person making his own mark, on a 3,000 year old technology.
Beam still on the mill I drilled and tapped for the locating pin and bolt holes that would marry the bed and Mr. I couldn't help but watch with admiration as he laid down a flawless continuous bead, which gave cause for me to place him right near the top of my list of heroes (be sure to let me know if I got that right, Ok Smitty?).



Best barns storage sheds jacksonville
Build a shed window xp

Category: Shed Company



Comments to «Woodshop lathe projects 8th»

  1. MARTIN writes:
    Any ceiling peak, and accommodates variety of mediums like wood or metal for them you'll be sent to our.
  2. Lenuska writes:
    Our CD cupboards and DVD cupboards wooden Shed Plans 6x6 Cedar The what different.
  3. TT writes:
    Building time is just 33 minutes, performed by 2 guys at Kauffman Builders In case you them.
  4. kommersant writes:
    The ends of the shelves to the aspect.
  5. ROCKER_BOY writes:
    DVDs can be bought your garage to return to being as cluttered.