Woodworking get wood stain,woodwork table plans xl,shed roof garage images workshop - Good Point

Woodturning has progressed enormously in recent years and is now no longer just a means of producing functional items, but is fast approaching the status of an art form. There are lots of very cheap lathes on the market that all look the same and appear to give you a lot for your money, photo 1. For this reason, it’s better to buy a lathe that is cast rather than fabricated, but this inevitably often involves greater cost.
A professional turner will probably need a heavy-duty floor-standing lathe, but for the home woodturning enthusiast a bench-mounted model will probably be quite sufficient, photo 4.
Several manufacturers provide leg-stands as an optional extra if you don’t want to build a bench. A homemade wooden bench is often better at absorbing vibration than a crude metal stand, and it can change the whole operation of the lathe.
The bed is made from either heavy metal bars or tubes, photo 7, but some machines still feature a flat cast bed. Whatever the construction, it must be strong enough to support both the tailstock and the tool-rest without any flexing, and allow free and easy movement of them both. Some imported models have what looks like a huge headstock, , photo 9, but when you remove the belt cover the two spindle bearings are actually quite close together. The headstock may be permanently fixed in line with the bed, or it may have the facility to swing round so that the spindle ends up at right angles to the bed for bowl turning, photo 12. I would rate this swinging head as an essential feature on a lathe; the real advantage is not only for bowl turning, but also for any turning where you have to work over the bed. If you are restricted with regards to space, many of the swinging head machines also allow you to move the headstock bodily along the bed, which is a great advantage if the end of the machine has to be up against a wall, photo 15. The headstock spindle is threaded to take a range of screw-on accessories such as chucks, photo 16, so you need one with a standard thread or you’ll be limited in the range of extras you can buy. This which means that you can then take all your threaded accessories with you, rather than renewing them with the lathe when you upgrade it. It is essential that your lathe is also equipped with Morse tapers in both headstock and tailstock.
There is a huge range of Morse taper kit on the market, but if you buy a lathe with only screw-on fittings you are very restricted as to what you can use. If the spindle is solid, there needs to be a centre ejector which screws onto the spindle nose before you insert the taper, photo 18. A small lathe will need a motor of at least 1⁄3hp, particularly if you envisage turning bowls, but bigger is better in this case.
The ultimate for speed changing is an electrical speed control, which gives you infinite variation of speed at the turn of a knob. State-of-the-art electronic speed controls have memory functions that can remember a selection of favourite speeds.
Whatever your motor type, make sure that the switchgear is easily accessible and doesn’t get hidden by large workpieces. Motors with a reverse facility are a valuable aid for sanding, and are quite safe to use on between-centres work. This needs to be as substantial as the rest of the lathe, as it has to provide fi rm support for between-centres work. The tool-rest assembly is another vital part of the lathe, the main requirement being that it is quickly and easily adjustable.
On the other hand, if you think your main interest will be bowl turning, a swiveling head is vital but between-centres capacity is less important.
If you want to do a bit of everything, try to decide on the biggest diameter you want to turn and choose a lathe accordingly. As you go further up the range you will find this extra power and solidity allows you to turn more quickly and confidently.
Above all, bear in mind that woodturning is an addictive hobby, so try to buy in as much spare capacity as you can afford now to save expensive upgrades later on.
Who doesn’t enjoy handmade arts and crafts?  Not only do they make excellent gifts, but buying them supports the artists and brings special uniqueness to your home.

Description: Our demonstrator Joe will give you some straight forward tips and advice on making your bandsaw perform the way you want it to when it comes to resawing and curve cutting. Description: Come see how simple and magnificent it is to create beautiful carvings using a drawing, a photograph, or a snapshot from your camera phone. You must have JavaScript enabled in your browser to utilize the functionality of this website. Unique and collectible wooden puzzle boxes are our passion at Puzzle Box World and we’re please to share these unique puzzle boxes with you.
To fuel this massive increase in popularity and demand, many woodworking machinery manufacturers have hurriedly added lathes to their range, but a good machine requires a number of essential features that are often overlooked in the rush to get new equipment onto the market.
These machines are very much entry-level models, being suffi cient to get you started, but if you progress much beyond very basic work you will soon fi nd them very limited.
Vibration is the woodturner’s worst enemy, particularly if the workpiece is long or out of balance, and there is nothing to beat sheer weight to minimise this vibration. However, do remember that unlike a lot of other machines, you will often spend hours working at the lathe. This is the height of the main spindle above the bed and therefore determines the maximum diameter of work you can turn, unless the head rotates round. These stands vary from a rather crude folded steel or tube arrangement, to a more rigid affair with provision for a tool shelf, photo 5. If you are short of space in the workshop, you can build in a lot of storage for tools or raw materials under the lathe, which also helps to give the structure a bit more mass, photo 6. This may be quite crude on the cheaper machines, or a work of art on top-of the-range models, photo 8. It must also permit shavings to fall through unobstructed and should sit well clear of the bench, so you can slide the tools underneath it without banging the sharpened edges.
Fabricated headstocks are rarely heavy enough if you need to turn large or out-of-balance work. A small bearing spread like this will causes problems with rigidity, particularly on large diameter work, so always look for a machine where there is plenty of distance between the bearings. Some machines have a tapered bronze sleeved bearing which gives much greater support than ball races, although it does require occasional adjustment. Swinging the head just a few degrees off-centre allows you to work with the tool handles clear of the bed, photo 13. On many smaller lathes, a thread size of ¾in x 16 tpi is the industry standard, which makes upgrading your machine less costly.
This is an important point, as you will often have a substantial investment tied up in chucks and other accessories. This is a universal means of installing centres and a range of other tooling, photo 17, and does not restrict you to using only the original manufacturer’s fittings.
Morse tapers are commonly No 1 or No 2 on the smaller lathes; the bigger the number the thicker the taper. Take great with these tapers and keep them clean and undamaged, or they will start spinning inside each other, which as well as causing them damage, will lead to inaccuracies when you are using fittings such as drill chucks.
In order to give some speed variation, the motor is usually fitted with a three or four-step pulley and a matching one on the spindle, photo 19, to give a speed range from about 400 to 2000 rpm.
This may be mechanical, where a lever operates two cone pulleys, so changing their diameter and therefore the speed, photo 20. This is usually reserved for the top-of-the- range lathes, but in the past electronic speed variation has suffered from loss of torque at low speeds. They can also sense incidents such as dig-ins and then instantly shut down the power, photo 22. However, if you engage reverse with a piece of faceplate work, there is always the possibility that it will unscrew itself, so lathes with reverse should feature a faceplate locking system.
The actual locking mechanism varies from machine to machine; some use a simple clamp and lever under the bed, whilst others use a cam type of lock, photo 26, which is easier to use as it is accessed from the front of the lathe.
For general use the rest needs to be about 10in (300mm) long, and made of heavy cast construction so that there’s no vibration when you are working at the end of it.

If you will mostly be turning spindles, then there’s perhaps no need for a swinging head model, but rigidity of the bed and good between-centres capacity are important features.
If you anticipate being an occasional user making a few simple furniture parts, then a basic model is all you’ll need.
You can take deeper and more ambitious cuts, and the ease of use of features such as electronic variable speed control make turning more intuitive and enjoyable.
The Oliver Intellicarve does it all very simply, allowing you to add carvings to box lids, cabinet doors, and furniture parts. Some even come with a stand and incorporate variable speed, but there is a defi nite correlation here between the price you pay and the quality you get.
Consequently it needs to be as smooth and quiet in operation as possible, so always think carefully about the quality and buy the best you can afford.
For anything remotely approaching serious work, you need a swing of at least 9in (230mm), but in practice the bigger the better.
The advantage of mounting it on your own workbench is that you can get the centre height just right – a serious consideration if you anticipate doing a lot of turning in the future.
Bear in mind that the performance of your lathe depends on how well it is mounted, so buy a leg-stand only if it looks man enough for the job. The headstock also needs to have a good spread between the bearings to ensure maximum rigidity of the spindle. However, when set up correctly this arrangement supports the spindle over a much greater length and provides totally smooth and vibration-free running, photo 11. Although you can still work off the standard tool-rest with the head swung a little, for big diameter bowl turning you will need an additional bowl rest to maximize the capacity, photo 14. The tapers just push into the headstock and are then knocked out afterwards with a bar that runs through the main spindle.
This is achieved with a belt, which is moved around on the pulleys to select the required speed. Fortunately modern electronic technology has largely overcome this problem, usually by operating a three-phase motor through an inverter off a single phase supply, photo 21.
Some machines have a magnetic switch-box, photo 23, which allows you to move it around at will depending where you are working. The tailstock barrel is moved backwards and forwards with the hand-wheel and needs plenty of travel for drilling work, photo 24.
For very long work there is a rest with two stems, but this requires an additional tool-rest holder. But if you think you will spend a lot of time at the lathe as your skills and ambitions grow, then you will need the extra power and weight of a larger machine.
This is a free demonstration with a factory trained representative to answer all your questions.
If this is your situation and you need some help, then this feature highlights the main factors you need to consider before you buy.
Incidentally, lathe dimensions are still mainly given in imperial measurements; for metric buffs the equivalents are 760 and 915mm. The traditional V belt has now virtually been replaced with the more efficient fl at poly V type, which gives a smoother, vibration free drive as it has no lumpy joint. It should be bored with a Morse taper to match the headstock, and should also be drilled right through to allow for easy removal of the tailstock centres and for long hole boring, photo 25.
Longer beds are available, and whilst these may appear attractive, they can add to any vibration problems unless they’re properly braced, so this is one instance where it is better not to buy too much capacity unless you have the specific need for it. So if you finished the last job at top speed and now want bottom, you firstly have to switch the lathe on and reduce the speed before you can mount the work, all of which is a bit fiddly and time consuming.

Reclaimed wood furniture in vancouver
Garden shed materials list ks1

Category: Wood Garden Sheds

Comments to «Woodworking get wood stain»

  1. KPOBOCTOK writes:
    However, floating hold heavy backyard tools metal storage cupboards To have the ability to enhance your garage.
  2. seymur writes:
    Wooden will guarantee a protracted however ensure to not rely on the make for flexibility.
  3. AnXeS writes:
    Errors arising due to the compatibility troubles storage and.