The most common type of boat snaps you will want to install on your boat canvas is Dot fasteners. An equally troublesome problem is the boat cover snaps actually pulling through the canvas from a tear or an enlarged hole. Professionals mostly use a Press-n-snap tool built by hoover to set snaps, but it is costly and over kill for the DIY boat snap installer.
Boat cover snaps can be set with an anvil style set tool as pictured below, but the press style snap tools do a more professional crimp. TIP The vice grips in this kit are bigger than average, so don't buy the dies by themselves because they may not fit on the tool you have at home.
Professionals install these fasteners using a expensive hand punch tool and again are not practical for the DIY boater.
The curtain fastener (twist fastener} and the Lift-The-Dot fasteners all come with two parts a€“ the 4 prong male top side and the female backing plate which sandwiches the fabric between itself and the male side, using the prongs to crimp down and hold tight the backing plate. Both of these boat cover snaps fastener can be installed with a little patience and without expensive tools. 8.Insert your male Curtain or LTD fasteners into the hole and crimp the prongs down over your female backing plate on the back side. After you drill any hole in fiberglass you will need to countersink the hole, this just means that you need to clean away the sharp edges of fiberglass from the opening of the hole.
Just spin the phillips head in the drilled hole while asserting pressure and you will clear away a nice opening as shown in the photo below. Now test screw by hand, your #8 screw stud or your Lift-the-Dot stud into your fiberglass hole, applying firm downward pressure as you twist . If as you go, you feel too much resistance and the fiberglass feels too thick stop (you are in danger of twisting of the screw, stripping your screw head or worse, cracking the fiberglass).
This will help you get a feel for drilling into the varying thicknesses of your boats fiberglass. You can install a screw stud into thin aluminum using the right drill bit and phillips head bit for putting in the screw.
If your boat snaps have pulled out of the fiberglass and left an enlarged hole, you have a couple of different choices.
First choice would be to try a screw stud with a #10 screw base and to see if it is large enough to hold in the fiberglass.
If the hole is still too large you can use a plastic drywall anchor like this one, they do come in varying sizes. Repairing your own screw studs and boat cover snaps is easy and something any DIY guy or gal can do for themselves. A Christian based children's home for boys and girls in crisis and in need of hope and healing. The isinglass had shrunk to the point that installing it was an all-morning job, with some snaps totally unusable due to the material shrinkage. I got a chance to install these yesterday and just thought I'd get back to you to let you know that they worked perfectly for me.
Tammy has become a valuable resource to my BoatButler business, and she has actually created sort of a "cult" following among my customers. With your zippers in place we could button up all of the canvas and make a very nice weather tight space which made our boating season very enjoyable.
I will be sharing your zipper solution with other boating friends and will be sure to mention the excellent customer service too. I have been hang-gliding and paragliding for thirty years and in that time I have gathered the knowledge to sew, stitch, repair and build all sorts of flying equipment, including release systems and hang glider carriers . Not only do I repair airsports equipment but I make bespoke covers for trailers, boats, cars, bikes, awnings for caravans and motor homes and repair kites and replace zips on tents also I manufacture tough high quality custom made bags. I am based near Norwich in Norfolk UK so if you need some heavy duty stitching then please give me a call or send me an email. Hang Glider Car CarrierMy hang-glider carrier allows your glider to be transported in safety on top of your car.
Trailer & Boat CoversI can produce custom made covers for many different items such as trailers, boats, cars and motorcycles. Before you make plans to repair a hole, you will want to check the integrity of the fabric.


Besides the boat cover repair fabric, you will need the largest thread your sewing machine can handle for this kind of boat cover repair. Another boat cover repair product on the market that works well as an adhesive patch is sail repair tape, and is available in most marine supply stores. Tent Pole tear repairIf your boat cover tent pole is the type that sticks through a grommet and your pole has ripped out the grommet, as long as it is a clean protrusion you may be able to repair it on your own using a tent pole vent called a Boat Vent IIA®. Tent Pole Through GrommettThese types of vents require a silver dollar size hole be cut into your cover. Mildew RemovalThe best way to prevent mildew is to keep the dirt from building up on your cover.The mildew grows on the dirt trapped in the weave of the fabric. We just installed the zipper we received on our sea ray boat canvas- what an incredibly easy experience!
The most common snap used on canvas boat covers are glove button fasteners, or durable-type snaps. Even though they look like glove buttons, note the words Pull the Dot on the top of the snap button. Rope tie downs are frequently used by boaters, especially when the boat is being towed, so it makes sense to buy rope that is going to hold up year after year. Boat Straps made with 1a€? webbing coupled with quick release buckles are easy to use and are a personal favorite. 12 pack - 8' long = $60.00(one 8' long strap reaches 4' to trailer) Need a different length? For an even more secure cinch, try a rope lock tie down such as the Carolina Rope RatchetA®. Another way to cinch your cover to the boat is with webbing in the hem along with the use of a webbing ratchet such as this Pro-GripA® ratchet. On boats that need additional tie downs while in the water, I've seen boaters attach 2 liter soda bottles filled with sand or water to the webbing tie down straps to add weight to the cover. Click here to see the rest of the form and complete your submission.What Questions Have Other Visitors Asked? Second knot on your boat cover tie down photos ? Can you provide more info on the second loop knot that you show on your series of photos ? I'm hearing the cover straps can cause abrasion to the hull, going down the road? Try to keep diesel exhaust off the boat's interior after driving to our destination. First make sure the canvas where the boat snap is being installed is reinforced so the snap will not rip through the fabric. Center the chalked prongs over your original snap mark on the fabric and touch the tips of the prongs to the fabric and transfer chalk marks. Flip your pronged male fastener over, position and mark the oval center hole that is between the four prongs.
Putting a block of wood under your fabric, use your tiny tip flat head screw driver and tap with hammer to punch the holes for your prongs.
Next use the same technique to start a pilot hole in the center, finishing with a pair of sharp scissors, carefully cutting the oval hole in the fabric. In 30 years doing this I did break a side windshield and getting the glass replaced was a huge pain.
I really was preparing to purchase a complete new canvas set, but hated to spend the money-especially since the canvas is still in excellent shape. When they're held by a person that truly cares about her customers, brings honesty, creativity and passion to her work, you have just described Tammy Hampton. I have been in to two local shops for estimates on a new canvas enclosure for my little boat. My repair services covers hang gliders, paragliders, kites, harnesses, sails, tents, boat and trailer covers.
It is manufactured at my Norfolk workshop and has been safety tested and approved by the BHPA. Read on to learn more about boat cover restoration, and save money (or potentially save your cover, rather than replacing the cover altogether!). Give your fabric the tug test, take hold of the fabric in both hands and see if it tears.If it does, then your money is better spent towards a new cover. So keeping your cover clean is your best defense.A question I get asked frequently is, "Can I put SunbrellaA® in the washing machine?" and "Can I pressure wash SunbrellaA®?"The best way to handle your fabric for cleaning is by laying it flat on a driveway, dock or grass and use a soft bristle long handle scrub brush.


Keeping your canvas boat cover free of dirt to start with is your best defense against mold and mildew, and will help you prolong the life of your boat canvas, which really does keep money in your pocket.
Dot fasteners and Fasnap are two common names.They consist of a button and socket which are crimped together and become the female snap in the canvas. Here is a list of webbing materials commonly used for boat tie downs, starting with the longest-lasting. I take them off each time and throw them in a bucket and when I put the cover back on I have …Click here to write your own. So if you are unsure of where your glass lays inside the metal windshield get help or hire a professional. Better known as "The Cover Girl," Tammy has been both a friend, mentor and business partner for nearly twenty years.
Both commented that they were happy to have a customer who knew what he wanted and was familiar with the material and options available. I am the past commodore of a Boat Club up here in the great lakes region and have many boating friends.
Tear-AidA® is flexible cut to size patch with a single sided aggressive adhesive that will stick to a variety of fabrics.The patches come in Type A for all fabrics including SunbrellaA®, and Type B for vinyls. Give your boat covers the tug test every year without fail, to check the integrity of your thread. Then you have the eyelet and stud that are crimped together and form the male snap in the canvas.
I am sure that once I show them how great your product works you will be getting more orders.
If you can do it yourself then go for it.Here is what a basic boat cover repair kit would look like. You just clean the fabric according to their instructions and stick the patch on both sides of the fabric, rub and you're done, instant boat cover repair! If you will do this faithfully, you may save yourself from costly repairs after a storm goes through your marina.
Screw it back together and insert the pole into the female receiver cup.The bonus of using the vent is that the hot air build-up under the cover escapes through the vent.
I don't mean where you grab it and turn it, I mean where you use the tip of your index finger to spin it in a circle and it moves freely. Select it and click on the button to choose it.Then click on the link if you want to upload up to 3 more images. She has yet to meet a challenge for which she could not find a creative and effective solution. In my opinion, nearly all boat covers should have this type of boat vent installed.Keep in mind that there does need to be a reinforcement patch in place before you install this type of vent. I can't tell you how many conversations I've had with customers on this subject and have been told many times that a€?my thread was finea€?.If you've gotten to the point where your thread is gone, you'll be looking for a shop to re-stitch your cover.
Use 1 cup to 1 gallon of water along with some detergent.Clorox is very tough on the threads, unless your threads are PTEFA® lifetime threads. Just a couple of things to keep in mind concerning thread: Ask the shop owner what kind of thread they use?
Using CloroxA® will absolutely shorten the life of your polyester threads, but the truth is sometimes the really tough mildew won't come out without it.
Do not use Nylon thread on boat covers, use the heaviest outdoor polyester thread your machine can sew with. Some fabricators carry PTEFA® thread which are lifetime threads, but since they are very expensive you may not find them everywhere.A 138 polyester thread should last 3 years in the most difficult tropical climates, 5 years in the south and more in the north. Just ask yourself if your thread will outlast your cover to determine if you should add the expense of re-stitching with PTEFA® thread.We now sell black and white thread in two sizes!



Junk sailboat plans
Boats for sale in gadsden al
Cheap plywood boat plans wooden
Pontoon boats for sale under 2000 uk


Comments to “Boat cover repair minnesota”

  1. AAA  writes:
    Seldovia your first port of name, your property port and celebrating train Stitch.
  2. SweeT  writes:
    Possibly opt for there have been was.
  3. BALACA_SIRTIQ_USAQ  writes:
    America, it is the will take danger for the boat buyer to ship boat.
  4. iko_Silent_Life  writes:
    Much less-salty bottarga to retailers, distributors, eating places and.