Lighted guide-on posts make it easy to load your boat onto your trailer and safer to transport it at night.
Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width. When your boat trailer has been backed down the ramp and is partially submerged, these 40" tall guideposts that are mounted at the rear corners of the frame will stick out of the water, giving you two highly visible targets to guide your boat between for loading.
Pre-Galvanized SteelPre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. We also offer a similar kit with 40-inch PVC pipes, part # CE27620, and a 60-inch kit # CE27760 that includes LED lights that mount on top of the pipes. The post-style guide-ons do need to be mounted as far back on the trailer frame as possible and as close to the boat as possible. I recommend the 36 inch Camo Guide-On Covers # CE27902 for your 40 inch CE Smith Posts # CE27740 instead, because these are designed to be open-ended to allow the LED lights to show. All of our hardware, we have our quick splice connectors that way we can easily tap into the wiring on our trailer. Sturdy well-built product that provides a great look to my new 21ft Sea Hunt and Venture trailer.
Instead of running the light wires between the tubing and PVC guides you can start at the short end of the galvanized tubing with a finish nail and thin string. Extremely pleased with the service and product - I will be back for my other trailer needs! I had purchased the Fulton boat guides earlier from another firm but had to return them because the U-bolts wouldn't work on my boat trailer (Not enough clearance between the u-bolt end and the bottom of my boat and I couldn't find replacements. Installation was a breeze, the quality is there, and will greatly aid in the loading of the boat onto the trailer. Unique and will suit my purpose but would be better if could be used as is for rectangular lights.
Great product came with everything needed to move your lights to higher points on your trailer.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information. We love helping people.We have the most highly trained customer service, hands-on experience, step by step videos and installation instructions. Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. We provide one-on-one, personalized service from the ordering process through the life of your product.


We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
They attach to the rear of your trailer and extend out of the water, providing visual targets to center the boat between during loading. The built-in LED lights on the posts stand out at night, making it easier for you to load your boat in the dark and for other drivers to see your trailer when you're on the road.
The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. This, with the U-bolt, with the little dent in it right here, will go over top of the other one. Considering that they are sealed LED units they are not likely going to go bad for a very long time. The built-in LED lights on the posts stand out at night, making it easier for you to load your boat in the dark and for other drivers to see your trailer when you're on the road. Typically mounted to post-style boat guides, these brackets help to keep the tail lights out of the water when you are loading or unloading your boat.
Our modern installation facilities allow our expert installers and customer service representatives to actually install and use the items we sell, so you can get real advice, from a real person who has the knowledge and expertise needed to solve your problem. We are prepared to answer any question, give advice, or troubleshoot any problem you come across. We take the quality of our information seriously so that you can get the right part the first time. The pre-galvanized steel support posts mount horizontally on top of or below your trailer's frame rail. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted. These wire leads will run down the inside of your PVC pole to be spliced into your existing trailer wiring using the included Scotch Locks. Installed and now my trailer lights will never see salt water again (unless I end up having a major oops moment).
Just slide the posts into the boat guide supports and secure the posts so that the distance between them correctly matches the width of your boat.
We'll go ahead and install it in place and what happens is, when you tighten down the bolts, everything clamps together. Before you get down to the end move our wire down beside the notch and push it down into place.All right, now at this point we can ahead and start to work our wires. The instructions don't cover my situation where the brackets had to be installed to a parallel trailer cross member. Galvanized steel is going to require certain products to be able to paint it and have the paint last.


Also included are two Ground Wire securing screws and two screws for securing the Top Lights to the PVC. Just slide the posts into the boat guide supports and secure the posts so that the distance between them correctly matches the width of your boat.Pre-Galvanized SteelPre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. Only issue is in order to remove the lights from the bottom of the trailer and relocate them to the guide poles you have to make 4 wire splices on each side and not enough wire splices come in the package. The cap and the post, PVC construction, where it goes down to a galvanized upright that is clamped on to the frame at the bottom.Now the goalpost is a good idea to load your boat up on your trailer when most of your trailer is submerged underwater. I'm going to route mine across this way and then towards the inside of the frame and then work our way to the wire harness or the nearest running light, makes it a little bit easier to attach. We're going to have all of our mounting hardware on this side as well as one of the LED lights. If you think about it you must first cut the wires where the lights are attached to the trailer and then splice the extention wires at this point using two of the wire connectors and then attached the wires to the light up on the guide poles using two more wire connectors. Guaranteed Lowest Price and Fastest Shipping for CE Smith Post-Style Guide-Ons with LED Lights for Boat Trailers - 40" Tall - 1 Pair. I visited my local West Marine to see if they had a solution & pressure treated 2x4 blocks under the brackets were recommended.
I just just did not install this one because I wanted to show what it looks like without it onto the PVC tubing. LEDs are going to be longer lasting and more energy efficient when compared to incandescent lights or incandescent bulbs.Everything is a really simple installation. Now the kit does come with a couple different screws, however, a self-tapping one may work better in this application. Once you have these installed, you want to install them as far back on the trailer as possible. You also want to install them to where the PVC piping is as close to the side or the surface of the boat as possible.
All of the hardware that you need for a complete installation is included as well as installation instructions.
In this case, the cap on top is still a little bit loose so we want it facing the right way, we want the amber color facing towards the front of the trailer and the red color facing towards the back. Okay and with that, that'll finish it for the CE Smith post-style guidons part # CE27740.



Houseboat rental branson missouri jobs
Wooden boat design contest guidelines


Comments to “Boat trailer guide post lights”

  1. rash_gi  writes:
    Fish and Wildlife have a superb educational Youtube video), I decided to try.
  2. RADIK  writes:
    The Fuji waterproof cameras sold on Amazon still be there bedroom suite for my child the.