Build your kitchen cabinets zimbabwe,wood plans free catalog code,how to make a computer desk at home 24 - Reviews

Regardless of whether you are building a stereo cabinet or dresser, a kitchen cabinet or bathroom vanity, basic cabinet construction is the same.
The carcass construction can be separated into three types: leg-and-rail, frame-and-panel, and box or case. Frame-and-panel construction is used to make up the component parts of many types of furniture including the sides, doors and interior web frames with dust panels that are used on many fine, hand-built pieces of furniture. Box or case construction is the basic design of dressers, buffets, desks and chests, as well as kitchen cabinets and bathroom vanities.
The following is the simplest method of constructing, using glue and finish nails that are then set below the surface and the holes filled with wood putty.
First step is to assemble the basic box, in this case of plywood, with glue and screws or nails. Cut the two side casings first, fitting them flush with the upper end of the sides and the lower edge of the toe space. Three winners will be chosen to receive the following prize packages, each will include: 1. In order to build kitchen cabinets, you need to have a proper plan and preparation, the right kind of tools and also a checklist of materials that you want to use or purchase.
A cabinet or furniture piece consists of the carcass or case with two sides, bottom and top, a back and a front. Leg-and-rail construction is found on chairs, tables, benches, stools and on some furniture such as chests. These can be softwood or hardwood plywood, and they can be painted or stained and varnished. If plumbing is to be installed for a sink, and electrical connections for a disposal are needed, measure and cut the openings at this time. Particle board, finished on one or two sides, is a common material for construction of some cabinetry.
Incidentally, you can construct a custom kitchen cabinet to fit any space, rather than the small individual sections joined as with purchased cabinetry.


The bottom shelf is raised above the floor on most cabinets to create a a€?toe-spacea€? or kick board.
The simplest method, especially for overlap doors, is to install veneer tape over the plywood edges. Next, transfer the measurements to the ?-inch plywood to saw it accordingly into the cabinet\’s back, side, top and bottom pieces. A case can also be constructed of solid wood, but these days solid wood is used only on small pieces or for extremely fine furniture.
Locate the position of the bottom on the side pieces and mark the kick board cut-out on each cabinet side. Then cut the lower facer to fit between the two side facers, ensuring the correct width to match the top edge of the bottom shelf and the bottom edges of the toe spaces on the sides.
Cut door and drawer dividers to fit between the drawer bottom facer or facers and the upper or lower facer as needed.
Upper cabinets are anchored to the wall with a nailer strip at the top and through the back into the studs, as well as with screws through the back into the studs.
After that, you need to assemble the cabinets according to your design and nail them together by using finishing nails and for more extra strength, do add some glue onto it before you start to nail them.
If a side is to be concealed against a wall, that side can be made of more economical plywood. A more traditional method is to install individual facer strips over the front edges of the case. To cut to length, cut one end smooth and square, then hold it in place and use a sharp pencil to mark the length. These can be anchored in place with toenail-driven, self-starting wood screws in countersunk holes, with glue and finish nails, or with glue blocks from the backside. Use a four-foot level to determine level and wood shingles as shims to ensure a level unit. Homemade cabinet jacks of 2-by-4’s with shingle wedges can be used to temporarily hold the upper case up in position and help level and plumb it until you can get it fastened solidly in place.


You can also use clamps for holding the frame together while waiting for the glue to dry thoroughly.
Locate the studs in the wall and fasten the cabinet in place with screws through the rear top nailing strip.
You also need to construct a face frame for the cabinet by using the 1-by-6 lumber so that it can be attached as the cabinet\’s door.
This can be done by cutting the 1-by-6 lumber into 4 pieces per each of the cabinet that you build. After that, you can attached the 1-by-6 pieces frame using the wood screws and also drill holes into the face frame so that you can attach them to the cabinet frame using nails. By pre-drilling holes on it will enable for the finishing nails to go through easily without damaging the plywood. You can do this by using the table saw and cut the plywood according to the mentioned sizes and then you need to sand the doors to make them look smooth.
Before attaching the doors onto the cabinet, you also need to apply stain wood and use polyurethane finish. Apply the first coat of stain and allow them to dry thoroughly before applying it for the second time. Once the second coat has dried, you need to apply a coat of polyurethane finish to the cabinet and leave it overnight before you start to install them the next day.
Finally, the task of installing the cabinets by attaching them to the studs where you have decided to place the cabinets.
You can use shims in order to properly set the level of the cabinets into the designated place before screwing them into the studs.




Step 2 toy box brown
Kitchen cabinet drawing detail englisch
Woodworking joints for table legs 07
Diy rustic headboard pinterest




Comments