Diy sliding door system,project management template with milestones,fine woodworking morris chair plans woodworking - Review

First, he got a piece of double track (the kind that’s attached to the top of mirrored sliding closet doors) and separated it in half- so instead of two tracks, there was only one track.
Great idea, perfect answer to a narrow hallway that my current door opens into, with the door gone, hallway gains an inch or so, and the door knob that’s always catching pockets and ripping pants would be gone!
Hey Juleen, I’m totally planning this project for my office, would you mind sharing a few more details?
Thank you for sharing – we have been looking for a barn door for our closet – will be doing this instead! I am remodeling my bathroom right now and I was trying to explain to my husband what I wanted for a door. If you used a heavy piece of crown molding turned upside down to receive the hardware setup, the top would be really unusual, and still come out far enough to clear the door frame. We haven’t tried this just yet, but I will be either ordering the $30 from Amazon or the $80 from the other site.
I enjoy writing and taking pictures, and adding pages to this place whenever inspiration strikes.
April 25, 2012 by The Accent Piece 133 Comments If you missed the first part, you can find it here. Hold it up to the door so you know how far to drill your hole.  Since the hanger will sit flush against the door, there needs to be a hole for the bolt to sit in. Then attach the rolling part to the hanging part.  I know, these technical terms can be overwhelming.
Now the hanger part fits flush against the top of the door since you drilled a hole for the bolt to slide in to.
Now that the hardware is installed on the door, you can install the box rail to the wall.  Find your studs (insert cliche joke about my stud being on the left in the picture below) and mark every stud. Oh my goodness… Hanging it was more complicated than making it but the results are amazing. I think it would look really good and work well to mill in both sides about half an inch or so and find inset plates for a door grab! Just google “sailboat hardware recessed” and you will find exactly what you need! Ironically Ive been thinking about installing a sliding door on our bedroom for a while, and if I can make it look good enough (with my limited woodworking skills;) then I might move on to other doors.
I can’t tell you how good it feels to get finished with a project that you’ve put your heart and soul into for months!
The rollers and track were fairly easy to install and I made sure to secure the red mahogany-stained pine brace to the wall studs perfectly so that it could support the weight of the barn door and track.
This project makes a huge impact on our space, creating incredibly beautiful and functional Art!
I do have a question for you, but first let me say that I am self-employed and make beautiful things for the interior design field. The first door I hastily put together was not finished, but I took it over to the furniture store, and left it with them so as to get some feedback. So cool that you are a creator of beautiful things for the interior design field, my major in college, btw… I could see how your creative process could quickly turn into life-numbing work after doing the same thing over and over. The steel being used in your door should definitely keep the wood in check, brilliant solution + who doesn’t love the aesthetic achieved from mixing wood with steel?!
Picking up where we left off, I had just finished my last piece of frosted glass in preparation for the closet door build. Since all of you are now very aware of my love for spray paint after yesterday’s post, the fact that I also use spray primer should not be surprising. Following the primer, I used two coats of Rustoleum Semi-Gloss white paint, making sure to sand in between coats.


We had some old hardware and track that was still inside of our closet, but it wasn’t pretty. It took quite a bit of prying off with my favorite needle nose pliers, but I finally got it up. Once I unscrewed each of the sides, there was another weird nail right in the middle of the track that I also pulled out. Now that the track and closet were ready to go, I headed back into the garage to finish up the closet doors. Since no one was ever going to see the inside of our closet, I was lazy and didn’t paint the back side of the doors. After all of my clips were secured, I flipped the door over and added the roller hardware onto the front as my handy bypass door kit instructions told me to do. About now was when I needed some serious man strength and asked Brad to hang the doors up for me.
Lumber: $25 (I had a few leftover 1x6s and a bunch of scrap that I never ended up using for another project.
You know, I never saw anything wrong with my builder grade sliding doors until now… Thanks! What if you put a frame around the glass (on the back side) instead of using the mirror clips.
I have a almost identical set of doors for the kidz closet, 340$ special order from Lowe’s 4 years ago. Tell me, if you only had the outside frame and the center member, with one sheet of glass, do you feel it would be strong enough to support it hanging? I love these doors and we are in the process of making them, Lowes will cut your glass for u for no charge, i got my glass there and it was 40ish dollars.
Enter your email address to subscribe to OPD and receive notifications of new posts by email.
We’ll definitely be trying it out here at TLC when we get around to working on our master bathroom door project! I found a kit at Home Depot specifically for this purpose and with the premade door it was all less than $60. We have since put in a double pair of french doors ($20 each from the habitat reuse store) that i frosted with window film ($18 from lowes) and i now finally have bathroom doors!!! Not sure if the price is lower than the double track (split) but it was definately less than commerical sliding door hardware. We used an inexpensive flat door, then covered both sides by designing and installing a laminate flooring. We’re about to move into a rental house that we hope to be in for the next few years while my fiance and I get married and finish grad school. You can even hide the upper hardware track if you want by offsetting a second piece of finished wood an inch and a half down, finished the same as the piece that is holding the track but perhaps not quite as thick dimensionally. I’ve always wanted an interior sliding barn door, but I never had the perfect and functional spot for one until we moved. The other materials were hard to come by, making this project take much longer than it should have, but worth the wait. I am extremely proud of my thriftiness on this project since barn doors and hardware online can easily reach into the thousands!
The most time-consuming part of this project was taking the pallets apart, but two hammers and some elbow grease are all that’s needed.
Barn doors can get extremely expensive, but if you’re thrifty and take your time finding the hardware, it becomes an extremely affordable project! Might I suggest doing small side projects for yourself, friends, or to sell on Etsy so that your passion stays alive?


In the case of your barn door, as long as you biscuit join each piece to the next & add a couple full length supports on the back, warp should be near non-existent. Not sure if I could go the glass route, but you’ve definitely got my wheels a-turnin! We have two closets buit into our attic space next to our dormer, and I have always hated the way the doors look. I really love that look and wanted one for our hallway, but barn door hardware is expensive, man! I have home depot and Lowe’s here where I live, and I’d LOVE to know how you did this!! The house is adorable, but definitely on the small side, and the closets in both bedrooms have no doors. My dad is doing a project like this for me, but we can’t seem to locate the double track piece. All of the closet door tracks I find seem to include a bottom track that they tell you to use, and I was worried about how much weight the top tracks will hold.
If that doesn’t work, we are thinking about drilling a small hole (but big enough to slide it with a couple fingers). Tell J that I wish some of his handy helperness would rub off on my J that is NOT into handy helperness! I found some old Cannon Ball Starline rollers on eBay for ridiculously cheap and scoured my town for a track to house the rollers, eventually finding just what I needed at PRO Build.
I also had to buy a piece of 1 x 6 pine to attach the track brackets to and of course bolts to screw the pine into the wall’s studs. I joined biscuits and used wood glue throughout and also randomly nailed to give it a well-loved look. The door looked a little lonely, so I found an antique four pane window on eBay and printed a picturesque mountain plains view to place inside, giving an expansive feeling when in reality it’s just a wall behind the window… so nice to have a mountain view here in Florida!
Me too! But check it out, I received an email from a sweet gal named Brier this week, and she and her hubby figured out an easy way to get the look for less. I tried to justify spending twice what we paid for the door itself on the hardware, but that didn’t fly. Luckily for us, my husband is a genius! I have painted the wood support beam the same color as the wall and it just about disappeared. Anything that opens out in the room would take up too much precious floor space and I wasn’t really thrilled about just hanging up curtains to cover them.
I wanted the wood of the barn door to look authentically aged so I oxidized it, well, my oxidizing specialist aka my adorable 5 year-old little guy, oxidized it & he did an amazing job! Maybe you could make a decorative wood frame or simply keep it frameless & paint the whole doorway frame the same color as the wall? There is room for framework, but mine does not have it since I wanted to keep it as light as possible in case my little monkeys, er kids, decided to hang from it, lol!
He’s a construction guy who bought the house and completely gutted and rebuilt it, so maybe he would even do it for us if we bought the materials!
When all was said and done the materials were about $96 and the finished project is worth every penny!
I was planning on trying to rig something up myself with random metal pipes and bars, because the prices I was seeing were just way to high. We have this opening between our bedroom and “sink nook” that I really want to add a sliding door to, and now I can thanks!



Wooden craft scrabble letters
Woodworking magnate router bits
Cloth toy box target audience
Golf shoe rack uk




Comments