Pvc diy dog bed bugs,build wood storage shed,barn door hardware 6 ft - 2016 Feature

An elevated dog bed keeps your dog off of the cold floor, and in warm the raised bed allows air to circulate under your pet. If needing screws in bulk contact Fastenal located at 295 Lewis Street, Fort Walton Beach, Florida or call at 850-302-0285 can be purchased for about $1.53 per 100 count. Fold each corner and slip the folded corner under the edge of the frame without moving the frame out of center. Add a total of about 7 to 9 screws (depending on the size of the cot you are making) on this one side to secure fabric to PVC.
Attach one screw through the fabric at the mid point of the PVC making sure that the screw penetrates all layers of fabric.
WARNING: STOP DRILLING AS SOON AS THE SCREWS ARE FLUSH WITH THE FABRIC TO PREVENT STRIPPING THE PVC!
IMPORTANT: IT IS EXTREMELY IMPORTANT THAT YOU PLACE SCREW HEADS NEXT TO THE EDGE OF FABRIC. This prevents the frame rail from turning which will cause the fabric to bottom out like a hammock and drag the ground. Hope you enjoy the videos and make sure to share pictures of your completed PVC dog beds and we’ll post them here for you! One of our most popular post of all time (believe it or not) was a DIY project on How to make your own Puppy Pen out of PVC Pipes! so when I found these How-To make PVC dog bed projects online.. BarkBox is a monthly subscription box for your dog and if you use our link below you get ONE BOX FOR FREE No Gimmicks!! Puppy Shopping ListHere is a page of all our recommended products for every new puppy owner.
I have added instructions below for materials and cutting for medium and small PVC dog cots as well as the original large PVC dog cots. All the general instructions remain the same — just use the correct set of measurements you need for your dog.
If you don’t sew I will be selling the slings for all three sizes so see Large, medium, and small dog cot slings for sale for details. Sarah contacted me yesterday asking if I could help her with measurements for a dog cot that would fit inside their dog crate. I had a reader request I sew one set of slings for the PVC dog cots and send them to her so she could then sew two more for her 3 dogs.
The first thing you will need to track down is the elbows that will be the corners of the bed. You can find the elbows on Amazon and they are also available at US Plastics and other places.
The important thing about the fabric is that it must be over 48″ in width (you will need to cut the selvages off). These instructions are written for someone with little sewing experience, so forgive me if you are an experienced seamstress.
A reader named Donna and I worked out the dimensions to make a smaller cot with 1″ PVC.


They are 3-way, but when I was shopping for parts I couldn’t find these corners in either of the big box stores. The 3 way fittings most hardware and plumbing supply stores carry are for household plumbing. I love McMaster Carr and never thought of checking them for PVC fittings — thanks for the tip.
I found the elbows on the Home Depot web site and had them shipped to my local store for free. We have two italian greyhound (overweight, haha) dogs and one bengal (evil and mischievous) cat. The PVC pipe cutter that he bought didn’t work, AT ALL, for the diameter of the PVC pipe that he had bought. I just wanted to stop by and say thank you for saving me a lot of mistakes while sewing this project. When I made my cots I wasn’t able to find the corners at all locally and had to order them over the internet. The elevated dog beds can be made to be water-resistant and not as welcoming to fleas as your traditional pillows or blanket type dog beds. Awning fabric (similar to Sunbrella) can also be used, but it is not as easy to disinfect or dry.
I just signed up for the BarkBox subscription box and if you use my link you get a FREE BOX!!!!Dang..
Since I had done my calculations for the new medium and small size cots in Excel I was able to come up with all the measurements fairly easily.
All that’s required are straight rows of straight or zigzag stitches so it would be a good beginner project. I recently increased the legs on mine after finding out one of my dogs has arthritis in her spine and I want to make sure she’s suspended above the floor. I use a T-square to square up the fabric and make straight lines for cutting, marking the lines with a chalk pencil and then cut. Cheaper threads aren’t of consistent thickness and will jamb up in the sewing machine. My expensive machine died and no longer had replacement parts available and I wasn’t in the mood to spend $1,500 to $2,000 on a machine. If you want to turn out a decent sewing project they are almost more critical than the machine you sew on.
I do three rows of stitching since these are the seams that will take the most abuse from the dogs jumping on the beds.
If you’ve sewn the slings to the correct length, the final corner should be a pain to assemble because everything will be tight. I don’t know if they carry them now, but local is always worth a check before having to pay for shipping.


My husband has already built the PVC bed (with my help) and he also used a miter saw to cut the PVC pipe. I was going to make it in just one big panel of fabric, but I like that yours is two panels.
Even my local plumbing supply house did not have the three-ways (called a 90 with a dog-ear).
I will send you an email to find out what size you’re thinking about and see if I can help with dimensions. Easy to care for and easy to clean and dogs LOVE them! The elevated design provides firm, even support which is beneficial to the orthopedic health of your pet.
If you have a smaller dog and want a smaller bed you will have to calculate different measurements. I always buy a little more fabric than required because fabric stores often don’t cut the fabric straight.
The 4th corner should be difficult to do — you may have to tilt the opening of the corner and work the pipe into it. I found the 3 way elbows at McMaster Carr for $13, but I picked them up localy (no shipping). They are commonly regarded as furniture fittings, not plumbing fittings so plumbing places probably don’t see the need to carry them.
If it were me I would definitely make the second cot — every dog likes to have his own place. Note: as the cots get smaller they are harder to get that last corner on so the medium and small are hard, but doable. I don’t have other sizes done but would be happy to work with you figuring it out if you come up with another size. Oh Well…because if you use my link I also get a free month AND once you sign up you get your own referral link to share with your dog lover friends! You want the fabric to be tight, so don’t get upset if it a bear to do the last corner. I’d like to say that I could figure it out on my own but I’m not so great at that!
BarkBox is a monthly Dog Lover Subscription box which includes toys, treats and fun goodies for the puppy in your life and believe me this will just save you time because you’ll be buying new treats and toys all the time anyway!



Woodshop projects box
Green woodworking pattern book pdf




Comments