Shopsmith first woodworking projects 8th,wood kitchen cabinet plans build,ikea coffee table lego - PDF Review

A while back, in a previous post, I talked about the news that Shopsmith was in financial trouble. The news today confirms it.
About 25 years ago, when I was first getting out on my own, I saw a Shopsmith woodworking machine at a woodworking show. Workpieces that are too small to be mounted on a faceplate or not long enough to be fitted between centers can be set up for turning by using a screw center (a device that is mounted on the Mark V main spindle).
When a project is longer than the spindle capacity of the lathe, it can be turned as separate pieces that are then joined in the manner shown in Figure 12-55.
The same idea applies when you join a faceplate turning to a spindle turning (Figure 12-56). When a large diameter is required in one area of the turning, two methods are used to prepare the stock (Figure 12-57). When solid stock large enough for a deep bowl or similar project is not available, stock may be glued together (Figure 12-58). You can produce intriguing lathe projects with an inlaid appearance when you prepare the base stock by gluing together pieces of contrasting wood. Procedures like this are useful when a special molding is needed or when you need a particular hardwood molding that isn't available. The two methods shown in Figure 12-63 can be used to prepare stock for projects like lamp bases before the material is mounted for lathe turning. Accurate center holes, of limited length when using conventional bits or much deeper when working with extra-long bits or extension bits, can be formed by mounting the drill chuck on the tailstock.
Some lathe projects, like wheel hubs, require radial holes that are equally spaced about their circumference.
The indexing disk, which is the control that positions a project for drilling, is made next. A typical use for the indexing device and a drill guide are shown in Figure 12-68, where the hub for a wheel is being drilled for spokes. The drill guide, made as shown in Figure 12-69, is mounted in the tool rest arm and positioned so the bit will be square to the work and so its point will be on the work's horizontal centerline. Indexing, as shown in Figure 12-70, can also be used to gauge the spacing of surface-drilled holes.
Model makers will find a dowel turning fixture almost indispensable for small turnings like head-lights, wheel hubs, rims, capstans, deadeyes for boat and automobile models, and for making components for miniature furniture.
A good feature of the dowel turning fixture, shown in Figure 12-71, is that it allows mounting of a long piece of dowel that is gripped for turning with the drill chuck that substitutes for the usual drive center. The most important part of turning a cylinder into an oval shape is the initial layout on the ends of the stock. First make an accurate template for locating the true center and the two off centers (Figure 12-74).
Here's a large, unique designed feeder that's a pleasure to look at -- PLUS -- it gives visiting lucky birds their choice of four seeds!


Start by cutting the four end pieces (A,B), deflectors (C), bottom (D) and the roof rafter (E) to length. Tilt your saw table to 45 degrees and cut the beveled edges of the deflectors (C) to form the pyramid-shape that will keep the seed moving down into the feeder.
Soon, the only place you’ll be able to read about them will be on the Old Woodworking Machines web site. Find the center of the workpiece and start a hole for the screw by using an awl or by drilling.
Extra-long lathe projects can be produced if you turn separate pieces and then connect them as shown here.
When a large diameter is required in one area of the turning, either (A) reduce the stock or (B) build up the stock. In one, start with oversized stock and use a jointer or bandsaw to reduce the stock before it is mounted on the lathe.
The mating surfaces must be perfectly flat and true for a perfect joint if the final turning is to resemble a solid piece of wood.
You can get interesting inlaid effects if you prepare a turning blank by gluing together pieces of contrasting wood.
The initial blocks can be prepared for either spindle turning (Figure 12-60) or faceplate turning (Figure 12-61). Good combinations to try are maple with rosewood, and holly or birch with cherry, walnut, or mahogany.
Using the paper-glue-joint method shown in Figure 12-62, two pieces of wood will produce identical half-round mold-ings. You can prepare stock this way when you need a lathe turning with a center hole such as a lamp base.
For example, if the hub is to have eight spokes, lock the indexing device at any point and drill the first hole. The indexing device and the drill guide can also be used to automatically space surface holes. The plans show three sizes of holes, but you can accommodate other sizes of dowels merely by drilling additional holes. It's a good idea to coat the dowel with paste wax to minimize friction where the dowel turns in the block.
If the ridge line is located first, it is easy to position the template at the ends of the stock and mark the centers with an awl. You can turn cylinders with an oval cross section if the work is shaped while it is mounted on off centers.
When the oval is complete, use sandpaper to smooth the project and to remove the ridge line.
Follow the pattern in the drawings and use your bandsaw or scroll saw to form the shapes on the ends (A,B).


Use some small brass or copper brads and weatherproof glue to assemble these two pieces together, then attach the assembly to the bottom using brads.
And the guy demonstrating it seemed to be able to switch over from table saw to lathe to bandsaw to drill press in no time at all.
And mail-order resources make almost any tool or supply available with a click of the mouse or just a phone call.
They’ve handed over day-to-day responsibilities to a consulting firm that specializes in financially-troubled companies.
On jobs ilke this it's best to use carbide-tipped tools since they have smaller cutting profiles than conventional tools. The blocks won't look like much to start; the appealing effects occur when the turning is complete. Four pieces of wood, paper-glued to a central core piece, will separate as elliptical moldings.
The plans for one that you can make and which is mounted on the Mark V's upper auxiliary spindle is shown in Figure 12-65. When the disk is engaged by the guide pin, lathe-mounted work will be held in a fixed position.
The table to which the fixture is clamped, or the power plant is moved to position the dowel for each new turning. When asked about their strategy, they said that they need to increase the value of the company by increasing sales. What does that mean? Lower prices?
The technique makes it possible to shape small items like drawer or door pulls, finials or small posts (Figure 12-54). Four pieces of wood, assembled as a solid block, will become four pieces of quarter-round molding.
Draw four lines along the length of the stock, connecting common perpendicular diameters at each end. This will establish the radius of the circle on whose circumference the guide holes must be drilled.
If the wheel needed four spokes, the device would be turned 90° to establish each hole position. Now divide each space into four equal parts and, with a heavy piece of paper as a guide, pencil-mark diagonal lines across each one as shown.
The important thing is a good glue job so the stock will hold together with just a faint line showing on the finished item. You must situate the holder so the guide pin and the spindle have a common vertical centerline.



Garden design jobs ireland
How to make a nice coffee table
Herman miller file cabinets parts
How to build your own sleeper couch




Comments