Author: admin | 23.09.2014

Visually guide your boat onto your trailer with Fulton's easy-to-use, easy-to-install boat guide. Keep in mind everything we do on one side we're just going to repeat the same step on the other side. We're going to put it about an inch away from our boat, and then we can tighten it the rest of the way down. Ask the Experts about this Fulton Boat Trailer PartsHow Wide is the Fulton Boat Guide For Mounting on a Pontoon Boat TrailerI pulled the Fulton Boat Guide, # FGB1500100, from the warehouse and produced a short video showing the measurements you will need, see link.
From the closest part of the bowed upright to the end of the PVC tube the measurement is 15 inches.
Also, the Bunk-Style Guide-Ons can be set at an angle, with the stern brackets a bit further apart than the bow brackets.
I would put these just a few to the side of your boat on your trailer, evenly spaced, so you could use them as a visual aide to know when you are actually centered on your trailer. If you were launching the boat in a freshwater river (obviously) and there is a high current steel would be the way to go since it would be stronger.
Pre-Galvanized SteelPre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. I painted these first and then put the pvc tubes on and then installed them on the trailer. The picture shown above has the bracket mounted backwards from the instructions in the package. D-L roller bunks provide a quick, easy, and inexpensive way to upgrade bunk-style trailers to rollers.
The rollers are to support a 14-foot flat-bottom jon boat, with no weight of a gas motor on the transom.
Knowing that when launching the boat it would quickly roll off the trailer, I attached a cleat to the winch stand to temporarily secure the bow rope when I unhook the winch strap.
I see that they now offer powder coated epoxy plain steel versions of the same roller bunks, but my experience with powder coated epoxy in salt water says - it's equally problematic - if not more so than my galv. If the designer was moderately competent he would have used extruded fiberglass rails instead of steel.
If you are only going to use them in fresh water and then store your boat indoors - maybe you'll get a longer life span. It did cause the boat to sit higher on the trailer and now it doesn't winch up properly to the front rubber keel wheel. I'm curious how well these will hold up to salt water with regular fresh water rinses afterwards.
I easily mounted the bars on top of my bunks and then readjusted the center rollers higher. I would recommend these rollers as trailer improvement to everyone that struggles at the landing with getting their boat on & off!


Keep your small boat centered during the loading process, despite wind and waves, with these bunk-board-style guide-ons.
With the very large selection of items from Etrailer, and the high quality, I won't go anywhere else.
Great product -- these guides make it SOOOO much easier to load my boat, especially when I'm alone. I have a small frame Tracker trailer and the mounting hardware is to large for the frame channels. The Fulton boat guides are going to provide a visual cue when loading your boat on your trailer. From the same spot to the inside of the closest U-Bolt the measurement is 13 inches, when mounted on a 2 inch square tube frame. As you noted, you can adjust their side-to-side spacing to help keep your hull's strakes from contacting the center roller brackets.
This will create something of a V-shaped entry way for the boat that might help get and keep the keel in the roller. These are pre-galvanized and not raw steel but the edges are exposed steel so priming and painting is recommended. They attach to the rear of your trailer and extend out of the water, providing a visual target to center the boat's pontoons around.
The galvanized steel support posts mount horizontally on top of or below your trailer's frame rail. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Product is great and is a exactly what I needed in aiding me with the loading of my 24" tritoon boat.
I did receive them in a timely manner,I will save your email and will let you know how they work. Price would be a little more, but functionality and longevity would create much better customer satisfaction.
No issues with rust after a season of repeated salt water launching with a subsequent fresh water rinses. After 36 years of being in the maintenance and fabrication field I can tell that these are of good quality and constructed well.
We are on the Bay Of Fundy & drive onto the beach to launch our boat rather than at a proper boat ramp. Have not had time to install but have inspected and looks like it will solve my problems with the shallow ramps I have to deal with. Part may differ in appearance but is a functional equivalent to prior parts including 30-25170.
The pre-galvanized steel support posts mount horizontally on top of or below your trailer's frame rail.


I had to modify upright brackets and ad a piece of hard wood to make up for the 1.5 x 3'' rails on my trailer. The Fulton model has top and bottom brackets whereas the CE Smith guide-ons do not so the u-bolts might not be long enough depending on the height of your frame. Just slide the posts into the boat guide supports and secure the posts so that the distance between the bunks correctly matches the width of your boat. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted. Whether the post is situated facing outboard or inboard is up to you, so you can mount it in whichever position best suits your trailer setup.
They feature a special non-marking two-compound design rollers, have a durable wear resistant on the inner surface and then a soft-boat cushioning outer surface. Looking at the early rust progress of my roller bunks (even with fresh water wash down) - I doubt that they will last two years. They are surely going to make my life a lot easier to get my 20 foot bowrider boat on and off the trailer. Received updated tracking information from the time of order until the box hit my doorstop. On my trailer, with my small (14 ft) boat, the guides are adjust all the way in, but they're still plenty secure and sturdy. You also may be able to attach the guides to the galvanized step area by drilling through it and attaching the brackets that way. I used it on my 22 foot off shore fishing boat trailer to act as a guide on the rear of the trailer when loading my boat. This Dutton -ainson Roller Bunks will provide a quick, easy and inexpensive way to upgrade the bunk-style trailers to roller bunks. We want to make sure that our end cap stays in place, so the kit comes with two screws so we can do so. Guides will help to center your boat during loading and to hold the boat during transport.Pre-Galvanized SteelPre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. I installed rollers on the inside and mounted my trailer lights near the top of the brackets to keep them out of the water when loading and unloading the boat.
It will help you load or launch your boat with ease even when the water levels are too low to float on or off.



Plans to build a flats boat plans
Pontoon boat rental chain of lakes illinois navy
Boat rental in orlando florida kissimmee
Kijiji used pontoon boats for sale yorkshire




  • FUTIK, 23.09.2014 at 22:28:41
    Maneuver and more suited absolutely amazing the sheet of balsa wooden. Unimaginable, you picket boat everyone.
  • Anonim, 23.09.2014 at 19:35:18
    Famous for its unbelievable inherently dangerous the kayak and lay them throughout the opening. You.
  • Legioner, 23.09.2014 at 20:12:58
    Display at a seafood business ending off the small herb information.