Metal shed base options 2014,plastic storage shed for garbage cans kitchen,sheds holden maine - Plans Download

The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience.
Tuindeco have a new metal shed range for this year and this will join many other brands of metal sheds on the market. With this in mind before I promote and sell this new range of metal sheds I’m writing this post to make you a little more informed, and, to offer you some advice on all metal sheds.
Towards the end of the post I will then walk through the installation of one of Tuindeco’s metal sheds which has some nice features setting it apart from others. You will be able to apply this advice to many other similar metal sheds and be armed with a little more information than is currently available online.
So, a good number of benefits here and reason enough to look at metal sheds as a solution to your own requirements.
Cost and Security are two major factors with metal sheds and you must realise that not all metal sheds are going to be secure just because they are made of metal. In the marketplace you will find one or two companies that list these sheds as security sheds and in my experience they are. But, these are expensive sheds and rightly so with the material that is in them often they are over 1mm in thickness and have special security locks.
If it is security that is your motivation then you need to look at these companies and perhaps do not need to read any further as I am not referring here to security based sheds. Do not think for one moment that a shed at this size under ?600 is going to be secure and despite what the seller tells you do not believe it. Metal sheds with a low price are designed for storage and price, they are not designed for security, do not be mislead. If simple storage and cost is your requirement then there a lots of sheds on the market including ours. Most metal sheds are bought online or from a catalogue these days and most companies are quite limited with the information they provide for several reasons. Within the industry metal sheds are regarded as a high volume product and a retailer expects to sell high volumes.
Don’t just base your decision on the price, understand that there are differences not immediately obvious of which I will try to explain a little more.
All metal sheds designed for storage and budget use the similar thickness metal sheet, ours have a thickness of 0.25mm which is actually thicker than a lot of metal sheds. Increased number of folds in this metal shed sees an increase in strength and resistance to denting. Metal shed folds – this is a picture of the roof of the new metal shed I recently installed, you can see the number of large folds which create the main strength, in between are small folds which add to the rigidity despite the thickness of the hot dipped rolled steel galvanised sheet used.
So, when you’re looking for a metal shed scrutinise the pictures from the supplier or ask the retailer about the folds in the steel panels.
All metal sheds will be fixed using a combination of nuts and bolts and self tapping screws.
If you can, try to find a metal shed that is supplied with Stainless steel screws and bolts.
Stainless steel screws and plastic washers to ensure a good seal without the need to silicon each fitting.
A very important area that differs quite widely with metal sheds is the strength of roof support. If a roof is specified for strength you would hope to find features such as the picture below.
Tuindeco metal sheds come with substantial roof supports, also supplied is galvanised brackets transferring the weight to the top rail.
Many metal sheds will only have a single center support so it maybe worth checking the strength of the roof before committing to a purchase. Like our log cabins, A Tuindeco metal shed is first built on the metal base rail that runs around the perimeter of the shed. In your research you are very likely to find that other companies will have this as an option and charge extra for it. Metal sheds have the advantage that they can be fitted to any surface so long as it is flat and a floor put in afterwards.
Also, if you haven’t done one before or are not experienced with plan reading, sometimes the instructions can leave you scratching your head for a while until you have figured out a particular point.
No matter which suppliers shed you choose the metal panels will ALL have sharp edges and they will cut you! Don’t try to install in a wind, I did with this build and it made it considerably harder with a greater risk of bending panels while it is unsupported.
This is pretty much the same as installing a log cabin or a timber shed but with a metal one there are a lot of screws to fix.
I admit to being sceptical as metal sheds are tricky things but I really do think this is a good shed when compared to everything else I have been involved in over the years.
Like any fitting process I always like to arrange the parts so I know what I have to deal with. One thing that pleased me was how well everything was numbered and straightforward to identify, other sheds I have installed took a little longer as parts need to be identified solely from the drawings. I was very pleased though, for the majority of the build, it all lined up nicely, you do sometimes have to pull the panels a little or send a screw through slightly at an angle but it all worked very well, I was pretty smug with the shed and enjoying the build, so far so good!
According to the instructions they asked for the first two panels to be placed as shown, it then asked for two to the back opposite these. I worked around the building rather than opposing sides as per the instructions, this was so I could stabilise it better against the wind. Up to this point everything had worked well, the holes had lined up but as I mentioned sometimes you have to pull the panel, handling the screws is also very fiddly. Then, a slight disappointment I did find two holes that were not correct this was the only time on the whole of the build and was the fascia strip that covers the front sliding rail.
I had hoped everything would be perfect but I did find one hole that needed drilling as it was out by a few mm. Once the top rails where installed the whole shed became a lot more stable and I was able to relax a little with the wind.
The apexes are made up of two parts and these screwed down into the top rail, again I had no problems with holes aligning. Fitting the roof panels was pretty straight forward and actually aided by the strength of the roof as I was able to lean on it to some extent.
When I fitted the ridge cap it did have a very slight bow upwards so I added an additional screw in the center, I also had the same with the leading edge trims so you might want to consider this. Up to this point the instructions were very good, despite this I still cocked up a few times as I didn’t pay enough attention. The completed shed after about six hours of work, a couple of cuts and a small amount of frustration caused by fiddly screws. And finally after a bit of swearing, a smattering of frustration and some cuts on my hand I was pleased with the finished metal shed. One small thing to note is that several of the panels has a protective plastic film on them. In hindsight this was wrong as it’s a real bugger to get off when all screwed together. If you choosing a metal shed for simple storage on a budget you can’t go too wrong with them. NOT a security shed – despite being made of metal, do not buy this type of shed thinking it has more security over a wooden one. Type of packaging – to ensure it arrives safely and you can store it until ready to install. This entry was posted in Metal sheds and tagged metal shed fitting, metal sheds, metals shed advice by Richard. Starting off square and level is essential to a successful shed assembly and we recommend that you consider a base kit to self-square the shed and help level the site. Base kits are not sized to fit GA Utility Buildings, Commander Series, Murryhill Utility Buildings, Mountaineer Series, Sentry Series, Ezee Series, SR1010, SR1011, NG63, CL72, HS108, all display units and Spacemaker products. In addition, they do not fit buildings that are the following sizes: 10'x11' (3,0m x 3,3m), 10'x10' (3,0m x2,8m), 10'x7' (3,0m x 2,0m), 10'x2' (3,0m x 60cm) , 8'x7' (2,4m x 2,0m), 6'x7' (1,8m x 2,0m), 10'x4' (3,0m x1,1m), 8'x4' (2,4m x1,1m), 8'x2' (2,4m x 60cm) and 6'x4' (1,8m x1,1m).
Arrow's shed accessories can help you make full use of your shed, maintain its attractiveness and maximize its lifespan. Large Item DeliveryMerchandise that is too large or too heavy to ship via package carriers are shipped via contracted freight companies.
If merchandise is damaged, indicate "damaged" on the paperwork, refuse at time of delivery, then call 1-800-851-1085 to re-enter order.

Arrow Storage Products is the leading designer, manufacturer and distributor of steel storage units delivered in kit form. This 8’ x 4’ Pent Metal Shed provides a secure and spacious area to store your garden items. Rates of finance offered in the calculator are based on this specific product and can be applied for once this item has ben added to the basket. This metal shed is designed to be hardwearing and durable and is ideal for storing larger items like lawn mowers and BBQ’s.
This Shed does not come with a floor but comes with a FREE Anchor Kit so you can secure it to concrete for a more stable shed.
The Aluminium Frame is a great material for the main structure as it is lightweight and strong. The Log Cabin is supplied with a comprehensive instruction manual and full assembly kit that makes construction as simple as possible. The item was easy to pay for, I kept the delivery info and I was waiting to be contacted by waltons confirming the estimated delivery time. I have bolted some metals rings on the concrete to secure my bikes and lawnmower as the shed is not secure!
The hasp and staple is only big enough to fit a travel luggage padlock on and the shed could be broke in to in less than a minuite, just by bending the flimsy doors or simply unscrewing the small door hinges off. I was pondering a few options, which were to build a shed from breeze blocks, wood or buying a metal one.
I like to get the best possible deals so looked all over to price the sheds up, I was going to buy from argos until i saw it was about 250 pound cheaper to buy the exact same shed from an ebay retailer, which was also brand new!!. The item description basically said allow for two weeks delivery, and on the Argos site it said up to 6 weeks so i wasn't expecting it to arrive any time soon which was a good thing as i was in the middle of doing some DIY in and around the house!. I looked at the instructions and found out the recommended size of the base, i also spoke to the neighbour who has a similar shed and learned they suffer from dampness getting into the shed when it rains (The rain basically runs from the base into the shed as it overhangs the roof a little too much). Once the base was created, i dropped it where i wanted the shed, thankfully and i cant believe it if i am honest, the base was completely level!
Once i had an even hardcore base, i decided to work out how much concrete this was going to take, i quickly found a concrete calculator online and put in the measurements. Now that i had all the materials and the base frame was made, the real hard graft was about to begin, all i will say is if you have never mixed sand, gravel and cement manually before, think twice! Wheel barrow after wheel barrow load went into the base (unfortunately i cant remember exactly how many barrow loads though and id rather forget the full experience if I'm honest). The weather was gash so i had to cover the base with tarpaulin so it didn't get waterlogged or it would have taken weeks to dry! The roof was lifted in place and fixed which strengthened everything up, i decided against securing the shed to the base for another week to allow the concrete enough time to fully cure. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. In a previous job I gained a lot of experience with these types of building and we sold all of the brands available. I remember a few customers being disappointed with the shed or that it was not what they were expecting.
My installation guide of a metal shed towards the end will also give you a reasonable overview on what to expect when you install yourself.
In fact at the office have a parcel drop box made by one of those companies and it is indeed very secure and very strong.
Tuindeco specified a thicker metal than usual but it still seems pretty thin doesn’t it? If you can find out the thickness of the steel this will help some of your decision process, but ….
I personally prefer self tapping screws used the most as it makes installation a lot easier and more secure with less likelihood of nuts coming loose. All Tuindeco metal sheds comes with stainless steel self tapping screws and bolts as well as plastic washers to help create a good seal. This is something that should be considered when you are deciding on which metal shed is for you.
This is the new Tuindeco metal shed I installed and I was very impressed with the roof structure. Please be-aware that they are quite light and will need to be fixed to the base if you are not using a foundation kit flooded with concrete.
If you are installing a larger shed which is going to run into two days make sure you support all the panels fully before leaving them overnight. I also need to make sure the product I am selling is a good quality or if a customer experiences it as less in their opinion I can at least defend it based on my experience of the comparable products available.
All metal sheds will be similar and this maybe helpful for you even if you have not bought one of ours.
A very strong box which is highly reinforced which should see our metal shed arrive safely and enable you to store it safely before installation.
This was one of my biggest concerns with these new sheds and one of the reasons why I wanted to put one together myself before we promote them. If I had done this I would have needed more helpers or support such was the wind on the installation day.
The instructions will show you which way these go and will show you to install them before you put the rail on. When you are fitting the roof supports keep an eye on the bracket supports, I installed the side ones wrong and had to take them off again.
Each side for this size shed is made up of two roof panels, the second roof panel did need pulling a little.
It’s not shown on the instructions and perhaps considered unnecessary but as I had lots of screws and bolts left over it was my own enhancement. When I started to do the door I did scratch my head at first but this is how it should go if you end up at the same head scratching moment.
A ventilated gable is very important in metal sheds to stop the build up of condensation which they can suffer if a damp proof membrane is not used or the concrete allowed to dry out properly. Overall though I think it’s a  cut above the rest of the comparable models in the same price range. I liked the colour as well, it blends in nicely and I can see it quite unobtrusive in the garden. I left most of it on during the install thinking this would be a good thing and help to protect it from me scratching it. Certainly ours I think is very good value for money with features that takes it above what others are offering. This can be limited with the use of a damp proof membrane on installation and making sure you buy a shed with ventilated gables, other factors can influence this and I will follow up on this is another post. The large Roof Strengthening Kits (RBK1012 and RBK1014) are considered large item deliveries and ship for a flat rate of $95. These companies will call you when your merchandise arrives at their terminal to set up an appropriate delivery time. Since it was established in 1962 as Arrow Group Industries, the company has sold more than 13 million sheds to customers around the world through its retail partners. This metal shed is designed to be hard wearing and durable and is ideal for storing larger items like lawn mowers and BBQ’s. The pent roof allows for extra storing space and the sloped roof design also prevents rain water from gathering therefore preventing rust.This shed also features double doors, which make storing and retrieving items from your shed hassle free. Up until recently the karts have been stored in my parents garage which wasn't so much of a problem but more of an inconvenience. When i weighed up the options, i decided against the wooden shed due to the yearly maintenance involved in keeping them in good condition (I'm far too busy).
However its still a lot of money to justify on a shed especially when we have just been on holiday, enjoyed one of my sons birthdays and have my other sons birthday approaching! I was actually in the middle of repainting the exterior of the house which was some crazy spontaneous idea of the other half when i heard the door bell. I like perfection so took this info on board and decided to make the base over hang the shed just half an inch on all sides. I waited a few days then mixed some sand and cement at a ratio of 6 parts sand to one part cement to finish it off as a top coat (floor screed).
Now i spoke to a lot of people regarding this who advised me it took them days, the instructions claim 6-8 hour for 2 men.
The roof was to be made separate and to be lifted on, so make sure you have a few people to help!

The metal is razor sharp, seriously I'm not kidding, the amount of slight scrapes that resulted in blood loss was unreal. The condensation the first few nights was unreal, i think this was because there was still some moisture in the concrete.
I might, and i say MIGHT, lay a course or two of bricks to heighten it, i would need a ramp to get the karts in and out, which i would build from wood. I am going to get some pipe insulation to cover the sharp rafters, so if you bang your head your not scalped. I am going to replace every self taper screw with a nut and locking bolt and even loctite them in place. Understanding condensation and damp is by far the most important thing, I've read loads about how metal sheds suffer from condensation and one of the main reasons is due to the base.
To strengthen the shed i aim to insert some aluminium bar above and below the one bar the standard beam that comes with the shed. To strengthen the doors, i will be attaching a lock on the provided handle as well as adding a lock at both the top and bottom of the door.
In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the Special menu.
I was almost at the beginning of metal sheds in the UK and at one point was with the largest retailer of them. This is hugely unusual as I have rarely seen a retailer even mention this and it should be a consideration. I haven’t seen this much support or depth of rafters in any other metal shed I have installed in my time.
In addition until you add the plastic protective tips (supplied with a Tuindeco Metal Shed) there will be screw tips showing inside and these are also sharp until covered (if supplied). Transportation and storage of metal sheds has always been a problem for every supplier but this appears to be solved with this packaging.
Some of these steel rails also form the foundation kit that I haven’t yet installed and were left over at the end of the build.
At this point I chose to ignore the instructions and worked around the building as I could stabile it better. I may have made a mistake working around the building as on the opposite side to this picture a panel was overlapped wrongly and flared slightly. As it was on the fascia though this was then covered by another panel and not seen so not really a problem. If you make a mistake with which way they go in you can take them out again – as I had to do when fitting the doors later – Doh! The top, middle and supporting rails are all installed inside the panel and not the outside as I first thought. Other sheds are green or blue or any myriad of colours and combination but this does hide itself well. The base kit must be assembled with your selected floor finishing option before you start to build your shed. This shed is designed to protect your possessions from weather damage and withstand strong winds. I mean i had to work around them to collect or work on the kart which was a nightmare if they weren't available when i needed access etc. I looked into the breeze block and although it would have been the best option decided against it due the the lack of funds at that moment in time. I sat there thinking, should i buy it, or shouldn't i buy it, in the end i left the computer and when i came back noticed the shed was bought and paid for. Once i knew the size, i went to the local wood store and bought some exterior treated wood, it was a bargain 14 foot long, 4 inch x 2 inch and under five quid!. I then went to B & Q to buy some gravel as i read that when concreting you should put a layer of gravel down to allow water to pass under or something along those lines.
The instructions don't advise you do this on a windy day and i understand why, i honestly thought the shed was going to end up on mars!!!
The panels basically self tap screw onto the frame, this means if a undesirable character wants to pinch your stuff, all they have to do is take screw driver and unscrew the panels (Its as simple as that) Also if you tighten the screw too much, they lose their bite!
For the panels that overlap which could be prised open with a crow bas very easily, i am going to drill and either pop rivet or nut and bolt them together. If a concrete base has been used with no damp proof membrane, then the moisture can travel upwards, evaporate and once it touches the cold metal surface (the roof) condenses. I may also consider copying the neighbours locking technique and use a bar or two across the doors too. I remember in my previous job complaints over a heavy winter of collapsed roofs, it’s not at all uncommon.
The problem comes that the screws and bolts are small so you do need to remove your gloves sometimes but keep in mind always they can bite!
When you install keep an eye on the instruction schematics and where the overlaps of panels should be. Use the flooring material that best suits your needs, such as wood, patio blocks, or gravel. It does not feature any windows making your items more secure.This metal shed is ideal if you are looking for a secure, low maintenance and hardwearing shed. I was confused lol, until the other half said the motherinlaw was going to buy it for me, as long as i paid her back. I bought 4 and asked the bloke to cut them to 10 foot lengths so they would easily fit in the car. I totally underestimated it and quite rightly so, after all I'm not a builder, far from it in fact lol. I was actually very impressed with the end result if i am honest, and when my dad returned from his holiday (he was skiving I'm sure), he too was impressed. Any ways we got started and i have to say, the instructions might as well have been written by an animal, I'm not kidding they didn't make sense and weren't very clear! I have two buckets of tanking left from a previous renovation job so i am going to tanking over the floor to ensure no moisture can penetrate.
At this point it’s a good idea to square it properly and fix down to your base if you have one at this point.
It size and design utilises space to store items and the quality build ensure this shed will last a long time. The total cost of materials for the base came to around ?80, which i think it fantastic when you consider its a solid reliable base requiring no further maintenance. I left them out until the end as you can then use the holes to hold the bolts for the roof supports and I didn’t need a helper which freed him up to make a cup of tea.
The carrier is not responsible for bringing merchandise into your home, uncrating, installing or removing packing materials.
This was a total nightmare, i had a big job outstanding, a shed that needed a base making and various other jobs to do.
At that point another stroke of luck, the other neighbour asked me if i wanted any old paving stones out of his back garden. As i needed bags of this stuff i thought the easiest most reliable way to mix would be use a bag as a part (4 bags of gravel, 2 bags of sharp sand, 1 bag of cement). If you need to make special delivery arrangements, it will be your responsibility to make those arrangements with the carrier when they call.
I basically cut the wood so the inside measurements measured one inch larger than the base required allowing for a half inch overhand each side. I know from when i was removing the old path in the garden the foundation was basically, broken up paving stones, bricks etc, so took them all. Each bag was 25 Kg so as you can imagine mixing 175 kg as one bach plus water was certainly a stamina tester. I smashed them up into small pieces which was hard graft, i spent hours to be honest breaking these paving stones up into workable pieces, laying them over the gravel.

Cedar tool shed kits 10 x 12
Tool sheds for sale gauteng yesterday

metal shed base options 2014

Comments to «Metal shed base options 2014»

  1. Boz_Qurd writes:
    Enabled DVD provided by Vizio are the Vizio VBR220W.
  2. EFQAN writes:
    More garage and attic - it's possible that Texas heat for every file earlier.