Magnetic pulse generator circuit breaker,free online film school 2013,earthquake survival plan,free movie editing software mov - How to DIY

A Multipurpose power pulse generator capable of driving Tesla Coils and other high power coils. This unit quite simply can generate high current pulses of variable frequency and pulse width.
A switch allows power to be sent to external coils for low voltage applications, or the internal ignition coils can be powered for charging a large HV pulse discharge capacitor. The low voltage circuit in this device is similar to the driver for the Homemade Tesla Coil, but with some important differences. All the power electronics are housed in an Aluminum case finished with panel meters, IO ports, and switches. The high voltage output from the ignition coils is rectified using some large high voltage diodes (D2) designed for X-Ray machines.
The main high voltage front panel on the box has sockets for HV DC output, an internal HV pulse discharge capacitor, and an internal spark gap.
All the high voltage cabling inside the box is placed inside flexible plastic tubing for added insulation.
The case is grounded by connecting a thick wire to a long metal spike driven into the ground. Connecting the case to the earth spike is essential when using the device to drive Tesla coils. The control circuit used for generating the driving signal is made using a 555 based circuit. External transformers, coils, or solenoids can also be driven at any desired frequency within the range of the 555 timer.

This device is capable of powering a multitude of experiments and is great for any researcher experimenting with pulsed power or resonant applications. Comments and questions for DIY Power Pulse GeneratorThe information provided here can not be guaranteed as accurate or correct. This device is based on the Homemade Tesla Coil project and uses an improved version of the ignition coil driver circuit to generate high voltages.
The high current pulses from the Lead Acid Batteries makes the signal generator unstable in the original design. They are not designed for high voltage use and will therefore leak a little energy by ionising the air nearby.
This allows the high voltage circuits to be configured in a number of different ways without having to re-wire any internal components. You can see here that the low voltage connections to the ignition coils are also covered with tubing for added protection. This is because a Tesla Coil (TC) will generate radio frequency (RF) currents that would otherwise become present throughout the circuit.
The double casing of the spark gap reduces the overall noise and allows the airflow to be doped with other gasses.The anode and cathode are spaced further than the voltage could jump and the third sphere can be moved in and out of the gap via a long glass fibre rod. This is not to improve quenching, but it will reduce electrode corrosion from Ozone buildup in the spark gap casing. This circuit can be found on the DIY Devices Page and is titled Signal Generator with Pulse Width Control.
The input signal is amplified using an array of nine 2N3055 power transistors (T2) which is capable of switching huge amounts of power.

The new version uses a completely independent signal source with its own battery to minimize the interference. This can be connected to the main unit via a shielded cable allowing it to be operated from a safe distance. From the smoothing capacitor an inductor (L1) and an additional 'de-Q-ing' diode (D3) have been added to the charging circuit to block the AC ringing from the TC primary coil from reaching the the smoothing capacitor. Depending upon the resonant frequency of the TC being driven, it may be necessary to adjust the capacitance.
Without a good RF ground you would probably receive little shocks from the controls when operating a Tesla Coil. This allows the spark gap to be adjusted smoothly anywhere between short and open circuit whilst it is active.
This feature also allows large or small DC motors to be powered with variable speed between 0% and 100%. There is also an extra buffer circuit to protect the 2N3055 Transistors from voltage spikes caused by the inductive kickback from the auto ignition coils. These also help to protect the the rectifier from short circuits, arcing currents and possible back EMF or transients.
It can be connected to the Power Pulse Generator by a jack plug on the end of the cable from the unit.

American red cross family disaster plan checklist
Emergency plan video production

Comments to “Magnetic pulse generator circuit breaker”

  1. V_I_P writes:
    Records an organisation requirements what occurs.
  2. 3770077 writes:
    Produced my head hurt which are perfect for placing collectively one's own most successful members acknowledge.
  3. Tuz_Bala writes:
    Rose close to 40 feet in some locations element.