N scale sound decoder installation instructions,new york boston best bus mumbai,n scale metra train set uk - Reviews

25.10.2015
See the instruction sheet for the particular decoder you are using for specific instructions.
FX3 decoders offer full function mapping so you can choose which function (F0-F12) controls each function lead.
TABLE IVc  The first hex digit of the FX3 CV value determines how the effect generated will behave. If you are using the ditch light effect in conjunction with F2, CV63 lets you set up a hold over time to control how long the ditch lights continue to blink after F2 turned off by releasing the key on the throttle. Any function output on the decoder can be set up for any FX3 effect by programming its associated FX3 CV to the appropriate FX3 CV value. In this case, the second digit of the FX3 control CV will always be 0 to set the decoder for static (no FX3)function operation. Digitrax uses series numbers to let customers know which feature set is part of a particular decoder. The fifth character of each mobile + function decoder part number is the Digitrax series designator.
Make Sure Your Item Needs To Be Repaired Before Sending It To Us!  Many of the units we receive for repair do not need any repairs at all. Many problems are easily resolved by contacting Digitrax Tech Support without having to send in your unit.
Once the shell is removed, remove the light board from the chassis by removing the small clip that holds down the motor tabs.
The chassis modifications I made were very simple modifications to provide support to the rear speaker, which is going to be installed in the location of the original rear headlight. Before installing the light board back on the chassis, insulate the metal contact strips that take power from the trucks to the light board with a small piece of kapton tape in the area where the motor tabs may contact them.
Once you are satisfied with the installation, you can slide the components back onto the chassis. Once I was satisfied with the fit of the decoder in the chassis, I glued the rear speaker to the two .100" styrene blocks that were installed to hold it. In order to let the sound out of the shell, you need to create an opening for the sound to escape. First, I cut the glass insert for the cab so that the cab insert could be slid straight down, instead of needing to be removed by sliding it backwards. Second, I cut the light tube for the front headlight so that I could pull the chassis out with with the tube attached, but still leave the headlight lenses in place.
I plan on installing a surface mounted LED for the rear headlight, but I have yet to make this installation.


DZ146IN - 1 Amp Series 6 NEM 651 Plug Decoder with 4 Functions that fits Many N & HO Locomotives!
Application Note: Steps needed for installing the DN143IP mobile decoder into the Con-Cor N-Scale Aerotrain "DCC Car".
This image shows the light board removed from the brass pins and shows how to pry out the dummy 8-pin plug.
This last image shows the DN143IP fully installed, with the light board snapped back onto the brass pins, ready for the body to be replaced. Each FX3 effect has a CV value that generates the effect you want and controls how the effect works with respect to locomotive direction and the head light (F0) function.
For example, two strobe lights can be set up to flash alternately by setting one to phase A and the other to phase B. Remember that F2 is a momentary key on most Digitrax throttles that will keep function 2 on as long as you hold the key down and then turn function 2 off when you release the key. Before you send any units for repair, please take a few minutes to review our Support Options. If a locomotive is sent to Digitrax, Digitrax will ship the entire package back, unrepaired. It shows the holes in the underbody, above which a speaker can be mounted for a sound decoder installation. Remember that the passenger windows of the car slanted forward toward the locomotive; it is easy to put the shell on backwards. In this case, you will be able to control the loco’s functions but the motor will not work.
Using TABLE IVa below, determine which CV you need to program to set up an FX3 feature for the function output you are working with. The first digit determines how the effect will work with respect to the locomotive direction, the head light and other functions. The strobes can also be set up to be on when the loco is moving forward and off when moving backward.
If you are using the PR1, an FX set up section is available where you can just "point and click" to set up the effects you want to use. This allows the ditch lights to be on steady during regular operation and to begin alternate flashing when F2 (usually the horn) is activated and to continue flashing alternately for a predetermined length of time after F2 is released; just like the prototype. For example, if the effect is set up to come on only when F1 and F0 are active and the loco is headed in the forward direction, be sure you have met those conditions. The recommended Digitrax sound decoder would be our SFX0416, but to use this decoder the seats will need to be removed.


Once the dummy plug is removed, carefully insert the DN143IP, making sure to orient pin 1 to the pin 1 hole. For example, if you want to set up an FX feature on your forward headlight, you will use CV49 to control the FX3 feature for the lamp attached to F0F. Use TABLE IVb to determine the second digit and Table IVc to determine the first digit of the FX3 CV value to program into the CV selected in step 1.
Values between the high and low allow you to vary whether the lamp actually goes off between light pulses or whether it stays on very dimly or more brightly. We recommend you start with a 4 and adjust it up or down until you get the effect you are looking for. A value of 00 yields no hold over time, a value of 40 yields a realistic time of about 5 seconds. Digitrax introduced FX in the summer of 1995 in all of its premium decoders so if your decoder was made before then it does not have FX capability. There is a pocket that is 16mm wide, 36mm long and 3mm deep designed for a speaker above the underbelly and under the seats. FX & FX3 decoders use different CVs for controlling the function outputs of the decoder.
The speaker that comes with the SFX0416 would need to be replaced with a speaker of the appropriate size. You do not need to remove the four black truck pick-up wires on the corners of the light board. See the specific decoder instructions to determine which "pad" on the decoder controls each function. To remove the body, carefully insert a flathead screwdriver between the diaphragm and the body where we have placed the arrows. They’ve been engineered to have enough play to raise the board high enough to remove the dummy plug and insert the DN143IP.
Use thin wire or wire saved during previous decoder installations to solder function output wires to the pads associated with the function you want to use.



Train brio 18 mois creche
Small n scale train layouts



Comments to «N scale sound decoder installation instructions»

  1. KISA writes:
    Globe class resource for N scale car passenger train subscription.
  2. LEYLISIZ_MECNUN writes:
    County Shopping Center, an indoor mall in San find myself drawn to a single location for.
  3. VirtualBaki writes:
    1988 with greater motors, more realistic paint value.
  4. SeNSiZiM_YuReKSiZ writes:
    License to manufacture replicas generalized your code to n scale sound decoder installation instructions handle any arbitrary DCC command size was very conveniently.