How to install a transducer on a pontoon boat used,how to fix leaking boat rivets uk,sport fishing boats for sale in australia queensland,used boats for sale in northern ca - You Shoud Know

Published 18.07.2014 | Author : admin | Category : Wood Boat Plans

I've been doing a lot of research on the best way to mount a couple things and I think I have the basics figured out on it. Once I do get the transducer angle set, is there any good ways of securing the cable to the pontoon as it makes its run up to the helm? Well, the new ladder is mounted and working very well, so its time to plan the next upgrade. It took awhile to get the pictures.The transomThe part of the dash that I am hoping to mount the dial. My hummingbird dash mount depth finder's transducer is mounted on the outside of the bracket on the back of my pontoon as seen in this photo. September 6, 2014 by Jim Harmer 14 Comments Before installing my fish finder on my pontoon boat, I spent 2 hours searching the web for a good tutorial on how to do it.
If you have a good tutorial and someone to help, installing a fish finder can be a quick and simple project that takes about 45 minutes. I wrote some handy tips on selecting a fish finder, as well as the one that I ended up choosing here. The transducer is the sensor that goes in the water that collects the data and sends it to the monitor.
You may find that the cord going from the transducer up to the monitor only has enough length to run off one of the pontoons.
Part of the problem I found was that I had selected a 7″ (18cm) screen for my fish finder.
Once you’ve found where the monitor will go, get down on the ground and slide up under the console to make sure none of the gauges or other wires will interfere with the cord run or the mounting of the fish finder. While you are down there, also see where the manufacturer has run the cords through the boat. Removing the siding of the pontoon boat can feel a bit scary, but it’s actually extremely easy and is usually only held on by about 10 screws.
With the siding removed from the side of the console all the way back to the rear of the pontoon, you will see where the manufacturer has snaked the cords. Once you have a clear path to place the wire inside the siding, put the plastic conduit shroud around the transducer wire and fish it through all the way up to the console.
While not really required, you may want to put just a glop of silicone on the holes in the console.
Last, drill an additional hole behind the bracket so you can put your transducer cord and power cord through. On my boat, I found that the factory had installed a fuse box with three accessory power fuses, and had empty connectors coming off the box.


With the empty accessory plugs coming off the fuse box, I simply bought a matching male connector and crimped it on the electrical positive and negative cord from my fish finder and plugged it in. Simply string the wires back from the front console back through the boat the same way you strung the fish finder cord. With option one or option two, exercise extreme caution when working with electrical and other aspects of your boat. I have a 2015 22' G3 Suncatcher V22RF Pontoon Boat that I use to tow the kids around the lake and fish for trout, bass, and kokanee. Personally I think that is low enough and to the side enough that if the engine is in the way at all it would be very little. Should I try to mount it on the transom or will it be fine next to the transducer on the pontoon? My biggest concerns would be at the very end of the pontoon, when it has to go up the end cap of the pontoon. Just make sure to use an inline fuse (1 Amp) from the power supply to the depth finder. You cannot drill holes in the pontoon and you don’t want it just loose so how do you attach it to the back of the pontoon? In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page. You will notice that the motor seems to block the transducer but all that is needed is a little tilt and it will shoot just fine.
Let me know what you all think if side scan should be ok mounted on the tab you see on the left outer **** in these pictures. I realize the speedometer may not be the most accurate or reliable, however the actual gauge was already there, I just had to buy the tubing and pitot. When I put the new motor on the boat 5 years ago, it had a pitot on it and I remember busting it off on accident in the process. I used the same transducer bracket and it was already mounted off bottom of the bracket and the transducer is well below the starboard pontoon lowest line. Suggestion: mount it on top of a pole that is mounted to, or over, the pontoon that has the transducer mounted on it. From what I am reading the SI only works at slower speeds so worse case scenario I just trim up the engine a bit to give it more room. I was sure that it was mounted on the transom but I can't find any sign on the boat of where it was. You need to remember that Pontoons squat in the rear, so bt tilting the back edge up, it will actually be pointing straight down when running.


I did read something about possibly needing a specially calibrated speedometer to use that feature. The way the instructions made it sound is that it was a pretty accurate science and you needed to be right on for it to work. With the 50 HP, you will probably not have the problems that boats with higher HP (faster) motors have. You may need to find some plate or angle or something to attach to the boat bracket to get your depth just right.
But since the sidescan only works at slower speeds that long transducer can be set not quite so deep and get a little protection protection from your boat. Considering I'm not going to be obtaining any record times on the water, I'm thinking it isn't as important. The faster your boats goes, the more critical it is to have the transducer aimed correctly. If you have anyplace to mount ahead of engine that will be in the water at slow speed I think it would work. The instructions include a nice tip using 12" of string at the transom to help determine the angle.
If it would work, or if I even knew how to try and see if it will work through the motor I would definitely love to give that a shot. Also, do I need to try to get the unit as close to the bottom of the pontoon as possible or does it really not make much of a difference in this application?
I've found on my last two Pontoons that the placement that I have shown in the pics above has worked best.
Since my bracket is about flush with the bottom of the log I might try to mount the transducer just above the bottom of it and see what it does. The transducer can be moved vertically by loosening the clamp, sliding the PVC tube up or down and re-tightening. Most say you want the transducer bottom slightly below the bottom of the log, but being a little higer has worked well for me.
Can I just use the power that is coming to the PS panel or should I run a seperate power for it?



Boat rentals near plymouth ma hours
Wooden speed boats for sale uk 600cc


Comments to «How to install a transducer on a pontoon boat used»

  1. dalina_smerti writes:
    Assortment, with wood rowboat, Our full boat typhoons (unfortunately reasonably design.
  2. sadELovh22 writes:
    And Boat Designs images I was a model railroader augustine plant, multiple buildings surrounded by overgrown.
  3. parin_iz_baku writes:
    Want to use along with plans, or who may want to improve Snarks pressure but has flexibility properties.