Diy bathtub couch,carpentry design london 02,pvc single bed sheet - Easy Way

Inspired by Holly Golightly's unforgettable sofa in Breakfast at Tiffany's, one Cote Maison reader decided to take matters into his own hands and DIY a clawfoot tub sofa for himself. With Instructables you can share what you make with the world, and tap into an ever-growing community of creative experts. Load the tub and claw feet into the car and take them over to a sandblaster (or use your own if you've got one).
My first step in attacking this beast was to make a small test cut just to prove to myself that cast iron could in fact be cut. As I mentioned before in the test cut step, be sure to wear full metal cutting safety gear. The other method for cutting cast iron that I wanted to try was the angle grinder loaded up with a 5" abrasive cutting disc. As you work your way along the cut line on the tub be sure to leave a few short tabs of cast iron approximately 1" long intact. Throw a standard grinding disc on the angle grinder and clean up any inconsistencies along the cut edge you just made. A second pass over the cut edge with a sanding disc loaded into the angel grinder smoothes everything out even further. Using new nuts and flange washers (the old ones I took off were heavily rusted), reinstall the claw feet onto the bath tub. Now here's what might be the most valuable part of this Instructable - a simple discussion of interior finishes for the claw foot bath tub couch.
This stuff will kill your brain cells in no time flat so make sure you wear a respirator and ideally paint in a well ventilated area.
Armed with a wide variety of sanders I set out to sand all the surfaces on the inside of the tub. Coming down the home stretch, all that's left to do now is to cut the custom foam insert and sew a cover for it.


Randy (randofo) and Gary (thirtytwooutside) take a well earned break from setting up for San Mateo Maker Faire 2012 by sitting on the claw foot bath tub couch. I think I am merely riding the groundswell of claw foot bathtub couch interest, as we all our - I simply have taken the time to document the process so that we may have the opportunity to make bathtub couches while hopefully learning a bit from my mistakes. The Interlux paint is specifically made for boats - seems like water exposure would be just fine. You are totally right about this - we have a group here in town that casts iron a couple of times a year, and we use plasma cutters to trim sprues and clean up overlaps and mold defects.
So I suppose one can't just order a half dozen from a local organic grocery store or anything, huh? I made one goofy face Instructable five years ago and it still lingers even after making over a hundred others since then! It seems a shame to sand and paint such a strong, durable and beautiful finish as porcelain enamel. When you buy a used tub off of Craigslist the porcelain will likely be badly damaged and stained. If you want to use it outdoors then I'd say to maybe just use the boat paint all over You can get it in other colors.
It would be cool if you took the lamp stand beside the tub and mounted a hollowed out shower head with a light bulb in it.
The entire surface gets sanded and painted so the excess of marker on the tub went away easily. Ideally the interior of the tub will be finished with porcelain and wont have any funky paint on it. Don't worry too much about the superficial condition, just rule out any significant damage or cracks.
I've worked for Instructables off and on since 2006 building and documenting just about everything I enjoy doing.


Kelley (icantbelieveshehasnousername) lies back and reads a book on a sunny California day many months later when I finally got around to properly photo-documenting this project in it's final form. After shedding the leather jacket and hair protection (angle grinding is tame compared to the circular saw ferrous blade setup) I slowly began tracing my cut lines with the edge of the ange grinder. Lesson learned: use a masonry abrasive cutting wheel on the inside of the tub to first cut cleanly through the porcelain. Sandblasting the porcelain on the inside will remove the shiny glaze and expose the porous interior of the ceramic coating. Lesson learned: sandblast before cutting and blast only the outside, not the inside porcelain coating. You might want to try using a powerfull jigsaw with a metal cutting blade, going nice and easy, on slow speed, It worked great cutting an old gas bottle to make wood burning stove. It is far simpler, to do than any kind of saw I can think of and like you mentioned literally lightning fast. That said, If i was going to use a saw, I think I would use a reciprocating saw instead of a circular saw and or grinder to make the cut. My wife wanted me to do this with our old claw foot tub and I told her it was impossible to cut!
I know it will defeat the idea of making it but I would really love to use it as a prop for my daughters birthday party. Try laying in a cast iron tub without enough cushions covering the metal.Brr r that's cold!



Table leg joints
Woodworking bench for sale deutschland
Cabinet makers wood glue
Golf carry bag reviews 2013




Comments